Diesel engine 1.8L car Ford Focus 1

Diesel Engine Specifications
Diesel Engine Specifications
Engine specifications - 75 hp. Name Code BHDA Firing order 1-3-4-2 Cylinder diameter 82.5 mm Piston stroke 82 mm Working volume 1753 cc Compression ratio 19,4: 1 Power...

Description and operating principle of the engine without fuel injection
Description and operating principle of the engine without fuel injection
Along with the familiar Zetec-SE and Zetec-E engines, this vehicle is equipped with the latest generation of diesel engine. It is called Endura-DI. This diesel engine,...

Description and operating principle of a fuel injection engine
Description and operating principle of a fuel injection engine
The Duratorq-TDCi diesel engine, which is available as an 85kW (115hp) option, is based on the renowned Endura-DI diesel engine but incorporates the latest technology...

Valve clearance — adjustment
Valve clearance — adjustment
Special tool Valve Adjustment Compression Tool 303-195 (21-106) Valve Shim Pliers 303-196 (21-107) General equipment: Set of feeler gauges. Name Specification Adjusting...

Valve Cover — Removal and Installation
Valve Cover — Removal and Installation
Removal All cars 1. Remove the top engine cover. 2. Remove the charge air cooler inlet hose, outlet hose and clamps. Discard the hoses and clamps as they are no longer...

Front Crankshaft Seal — Removal and Installation
Front Crankshaft Seal — Removal and Installation
Special tool Universal Flange Holding Wrench 205-072 (15-030A) Bolt Tightening Angle Gauge 303-174 (21-540) Crankshaft Seal Remover 303-293 (21-143) Oil Pump Alignment...

Valve Seals — Removal and Installation
Valve Seals — Removal and Installation
Special tool Valve stem oil seal installation tool 303-037 (21-007 A) Valve Spring Compressor 303-060 (21-024) Adapter for 303-060 303-060-05 (21-024-05) Device for...

Camshaft — removal and installation
Camshaft — removal and installation
Name Specification Motor oil WSS-M2C912-A1 Sealant WSK-M2G348-A5 Removal 1. Remove the timing belt. For more information, refer to the Timing Belt chapter in this...

Camshaft Seal — Removal and Installation
Camshaft Seal — Removal and Installation
Special tool Crankshaft Oil Seal Remover 303-293 (21-143) Camshaft Oil Seal Installer 303-199 (21-110A) Removal 1. Remove the timing belt. For more information, refer to...

Timing Belt — Removal and Installation
Timing Belt — Removal and Installation
Special tool Universal Flange Holding Wrench 205-072 (15-030A) Crankshaft Top Dead Center Pin 303-193 (21-104) Engine Support Beam 303-290A (21-140A) Adapter for...

Cylinder head — removal and installation
Cylinder head — removal and installation
Special tool Engine lift bracket 303-122 (21-068A) Bolt Tightening Angle Gauge 303-174 (21-540) Clamp removal/installation tool 303-397 (24-003) Name Specification Motor...

Cylinder head of a fuel injected engine
Cylinder head of a fuel injected engine
Special tool Engine Lift Bracket 303-122 (21-068A) Bolt Tightening Angle Gauge 303-174 (21-540) Engine support crossmember 303-290A (21-140A) Adapter for 303-290A...

Oil pan — removal and installation
Oil pan — removal and installation
Special tool Hammer with movable striker 205-047 (15-011) Adapter for 205-047 303-633 (21-227) Name Specification Sealant WSE-M4G323-A6 Motor oil WSS-M2C912-A1 Removal...

Rear Crankshaft Seal — Removal and Installation
Rear Crankshaft Seal — Removal and Installation
Special tool Bolt Tightening Angle Gauge 303-174 (21-540) Flywheel Locking Tool 303-393 (21-168) Removal 1. Remove the clutch disc and pressure plate. For additional...

Removing the engine
Removing the engine
Special tool Ball joint puller 211-020 (13-006) Coolant Hose Clamp Remover/Installer 303-397 (24-003) Axle puller 308-192 (16-057) General equipment: Workbench Fixing...

Disassembling the engine
Disassembling the engine
Special tool Hammer with movable striker 205-047 (15-011) Universal Flange Holding Wrench 205-072 (15-030A) Flywheel Locking Tool 303-393 (21-168) Clamp...

Disassembling a fuel injected engine
Disassembling a fuel injected engine
Special tool Hammer with movable striker 205-047 (15-011) Universal Flange Holding Wrench 205-072 (15-030A) Flywheel Locking Tool 303-393 (21-168) Clamp...

Cylinder head — disassembly and assembly
Cylinder head — disassembly and assembly
Special tool Valve stem oil seal installation tool 303-037 (21-007A) Valve Spring Compressor 303-060 (21-024) Adapter for 303-060 (21-024) 303-060-05 (21-024-05)...

Fuel Injected Cylinder Head — Disassembly and Assembly
Fuel Injected Cylinder Head — Disassembly and Assembly
Special tool Engine/Differential Mounting Bracket 205-329 (15-105A) Valve stem seal installation tool 303-037 (21-007A) Valve Spring Compressor 303-060 (21-024) Adapter...

Engine assembly
Engine assembly
Special tool Universal Flange Holding Wrench 205-072 (15-030A) Bolt Tightening Angle Gauge 303-174 (21-540) Crankshaft Top Dead Center Pin 303-193 (21-104) Camshaft Seal...

Fuel injection engine assembly
Fuel injection engine assembly
Special tool Universal Flange Holding Wrench 205-072 (15-030A) Bolt Tightening Angle Gauge 303-174 (21-540) Crankshaft Top Dead Center Pin 303-193 (21-104) Camshaft...

Engine installation
Engine installation
Special tool Clamp removal/installation tool 303-397 (24-003) General equipment: Workbench Fixing clamp Name Specification Anti-seize lubricant SAM-1C9107-A All cars 1....




Focus 2 
Focus Turnier 1 
Focus 1