Car rear suspension Ford Focus 1

Rear Suspension Specifications
Tightening torque specification Name Nm pound-foot pound-inch Bolts for fastening the anti-roll bar to the crossmember 48 35 - Bolt securing stabilizer link to rear...

Description and operating principle of the rear suspension
All except station wagon variants" Pos. Spare Part No Name 1 - Crossbar 2 - Upper arm 3 - Front lower control arm 4 - Shock absorber assembly 5 - Trailing arm and...

Wheel hub (15 373 0) — removal and installation
Removal All cars 1. Remove the dust cap. Cars with rear disc brakes 2. Remove the rear brake disc. For additional information, refer to Section 206-04. 3. CAUTION: To...

Wheel bearing — removal and installation
Special tool Primary Shaft Oil Seal Installation Tool 307-210 (17-041) Removal All cars 1. Remove the wheel hub. Cars with anti-lock braking system 2. Remove the wheel...

Wheel hub bearing — removal and installation
Special tool Bearing installation tool for axle shaft 205-146 (T80T-4000N) Steering Gear Oil Seal Installer 211-140 (T88C-3504-DH) Device for installing the holder of...

Front lower arm (15 690 0) — removal and installation
Removal 1. Remove the wheel and tire assembly. Refer to Section 204-04 for additional information. 2. Set the suspension to the design height. Refer to Section 204-00...

Rear lower arm (15 693 0) — removal and installation
Removal 1. Remove the wheel and tire assembly. Refer to Section 204-04 for additional information. 2. Set the suspension to the design height. Refer to Section 204-00...

Upper arm (15 701 0) — removal and installation
Removal 1. Remove the wheel and tire assembly. Refer to Section 204-04 for additional information. 2. Set the suspension to the design height. Refer to Section 204-00...

Anti-roll bar (15 752 0)
Removal 1. Remove the wheel and tire assemblies. Refer to Section 204-04 for additional information. 2. Remove the springs. For more information, refer to the Spring...

Wheel knuckle (15 366 0) — removal and installation
Removal All cars 1. Remove the wheel hub. For more information, refer to the Wheel Hub chapter in this section. Cars with anti-lock braking system 2. Disconnect the...

Shock absorber (15 791 0) — removal and installation
Removal 3-, 4- and 5-door version 1. Detach the cargo area trim panel and place it aside. 2. CAUTION: Use an Allen key to prevent the piston rod from turning. Remove the...

Shock absorber — universal (15 791 0)
Removal 1. Remove the rear wheel and tire assembly. Refer to Section 204-04 for additional information. 2. NOTE: When removing the left shock absorber, it is necessary...

Shock absorber — 3-door/4-door (15 791 0)
Removal 1. Detach the cargo area trim panel and place it aside. 2. CAUTION: Use an appropriate wrench to prevent the piston rod from turning. Remove the upper shock...

Spring (15 621 0) — removal and installation
Special tool Compressor for coil springs 204-167 (14-042) Adapters for 204-167 204-215 (15-111) Removal 1. Raise and support the vehicle. Refer to Section 100-02 for...

Spring — 3-door/4-door (15 621 0)
Removal 1. Remove the rear wheel and tire assembly. Refer to Section 204-04 for additional information. 2. Using an appropriate spring compressor, compress the spring....

Spring — universal (15 621 0)
Removal 1. Remove the rear wheel and tire assembly. Refer to Section 204-04 for additional information. 2. Disconnect the anti-roll bar from the rear lower arms. 3....

Cross member — removal and installation
Special tool Compressor for coil springs 204-167 (14-042) Adapters for 204-167 204-215 (15-111) General equipment: Transmission jack Bridge stand Fixing clamp Removal 1....