Elements of the car body Ford Focus 2

Features of the body design
Features of the body design
The body of Ford Focus II cars of the four-door sedan, five- and three-door hatchback or five-door station wagon type is of load-bearing structure, all-metal. The body...

Possible body malfunctions, their causes and methods of elimination
Possible body malfunctions, their causes and methods of elimination
Cause of malfunction Method of elimination Dark spots all over the body surface Application for washing with hot water (above 80°C) Minor damage can be repaired by...

Removing and installing the radiator grille
Removing and installing the radiator grille
Radiator lining 1 is attached to the engine compartment frame with two pins a and is held at the bottom by two clamps that fit into the grooves of the front bumper. To...

Removing and installing wheel mudguards and fender liners
Removing and installing wheel mudguards and fender liners
The front and rear wheel arches are fitted with plastic mudguards that protect the body from the abrasive effects of sand and stones thrown up by the wheels. Mudguards...

Removing and installing the front bumper
Removing and installing the front bumper
You will need: TORX T25 key, 10 mm socket head, flat-blade screwdriver (or piston puller), Phillips-blade screwdriver. 1. Open the hood and place it on the support. 2....

Removal, disassembly and installation of the rear bumper
Removal, disassembly and installation of the rear bumper
You will need: all the tools necessary to remove the mudguards and rear wheel arch liners ( see "Removing and installing wheel mudguards and fender liners" ), as well as...

Removing and installing the front wing
Removing and installing the front wing
You will need: a wrench and a 10 mm socket head. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the mudguard… 3. …and the front fender liner...

Removing and installing the engine compartment frame and the front bumper beam
Removing and installing the engine compartment frame and the front bumper beam
You will need: all the tools needed to remove the mudguard and engine crankcase protection ( see "Removing and installing the engine mudguard" ), radiator grilles ( see...

Removing and installing the air intake box grille and water drain shield
Removing and installing the air intake box grille and water drain shield
The air intake box grille and water deflector shield are removed if they are damaged or to gain access to the windshield wiper, as well as when replacing the windshield...

Removing and installing the hood
Removing and installing the hood
You will need: a 10 mm socket head and a flat-blade screwdriver. USEFUL TIP: To avoid injury and damage to vehicle parts, remove the hood with an assistant. 1. Open the...

Removal, installation and adjustment of the hood lock and its drive
Removal, installation and adjustment of the hood lock and its drive
You will need: a 10 mm wrench and a 13 mm socket head. To remove the hood lock do the following. 1. Open the hood and place it on the support. 2. Remove the radiator...

Removing and installing the fuel tank filler pipe hatch cover
Removing and installing the fuel tank filler pipe hatch cover
You will need: TORX T20 key, Phillips-head screwdriver. 1. Remove the right rear fender liner ( see "Removing and installing wheel mudguards and fender liners" ). 2. In...

Removing and installing the fuel tank filler pipe hatch lock
Removing and installing the fuel tank filler pipe hatch lock
You will need a flat-blade screwdriver. 1. Remove the fuel tank filler pipe cover assembly with the bracket ( see "Removing and installing the fuel tank filler pipe...

Replacement of fixed body glazing
Replacement of fixed body glazing
The windshield, rear window (rear door) and side window glass are glued into the body openings. They are replaced using the same techniques, so the work is shown using...

Removing and installing the battery mounting shelf
Removing and installing the battery mounting shelf
The battery mounting shelf is removed for replacement if it is damaged and to gain access to other vehicle components. You will need a 10mm socket head. 1. Remove the...




Focus 2 
Focus Turnier 1 
Focus 1