Vehicle switches and sensors Ford Focus 2
Replacing the external lighting control unit
1. Disconnect the wire from the negative terminal of the battery. 2. Remove the left instrument panel trim ( see "Removing and installing the instrument panel" ). 3....
1. Disconnect the wire from the negative terminal of the battery. 2. Remove the left instrument panel trim ( see "Removing and installing the instrument panel" ). 3....
Replacing the instrument panel switches
You will need: TORX T25 key, flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the center instrument panel trim ( see...
You will need: TORX T25 key, flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the center instrument panel trim ( see...
Replacing the hazard warning switch
You will need a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the center instrument panel trim ( see "Removing and...
You will need a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the center instrument panel trim ( see "Removing and...
Removing and installing the antenna
The antenna is mounted on the roof of the car, front and center. You will need a TORX T25 key. 1. To remove the antenna, unscrew it from the bracket by turning it...
The antenna is mounted on the roof of the car, front and center. You will need a TORX T25 key. 1. To remove the antenna, unscrew it from the bracket by turning it...
Replacing the oil pressure warning light sensor
The oil pressure warning light sensor is screwed into the cylinder block wall on the left front side of the engine above the oil filter. You will need a 24mm socket...
The oil pressure warning light sensor is screwed into the cylinder block wall on the left front side of the engine above the oil filter. You will need a 24mm socket...
Checking and replacing the fuel level indicator sensor
The fuel level indicator sensor is installed on the fuel module. To check the sensor you will need an autotester. 1. Disconnect the wire from the negative terminal of...
The fuel level indicator sensor is installed on the fuel module. To check the sensor you will need an autotester. 1. Disconnect the wire from the negative terminal of...
Replacing the pressure sensor in the power steering system
The power steering pressure sensor is screwed into the power steering pump housing. You will need a 13 mm wrench. 1. Disconnect the wire from the negative terminal of...
The power steering pressure sensor is screwed into the power steering pump housing. You will need a 13 mm wrench. 1. Disconnect the wire from the negative terminal of...
Checking and replacing the reverse light switch
The reverse light switch is installed in the upper part of the gearbox housing. You will need a 22 mm wrench. 1. Disconnect the wire from the negative terminal of the...
The reverse light switch is installed in the upper part of the gearbox housing. You will need a 22 mm wrench. 1. Disconnect the wire from the negative terminal of the...
Replacing the brake light switch
The brake light switch is mounted on the brake pedal bracket. 1. Disconnect the wire from the negative terminal of the battery. 2. Squeeze the latch… 3. …and disconnect...
The brake light switch is mounted on the brake pedal bracket. 1. Disconnect the wire from the negative terminal of the battery. 2. Squeeze the latch… 3. …and disconnect...
Replacing Cruise Control Switches
The cruise control switches are mounted on the brake and clutch pedal brackets. You will need a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal...
The cruise control switches are mounted on the brake and clutch pedal brackets. You will need a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal...
Replacing the Parking Brake Indicator Light Switch
You will need: an 8 mm spanner and a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the rear part of the floor...
You will need: an 8 mm spanner and a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the rear part of the floor...
Emergency fuel shut-off button
NOTE: The emergency fuel shut-off button is only installed on vehicles with gasoline engines. You will need: a 7 mm spanner and a flat-blade screwdriver. 1. Disconnect...
NOTE: The emergency fuel shut-off button is only installed on vehicles with gasoline engines. You will need: a 7 mm spanner and a flat-blade screwdriver. 1. Disconnect...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Focus 2
Focus Turnier 1
Focus 1
- General information
- Vehicle device
- Owner's manual
- Faults en route
- Maintenance
- First maintenance
- Second maintenance
- Applications
- Consumables and spare parts
- Auto mechanic tips
- Power unit
- Engine repair
- Engine seal parts
- Cooling system
- Exhaust system
- Supply system
- Clutch
- Car gearbox
- Front wheel drives
- Chassis
- Front suspension
- Rear suspension
- Steering
- Brake system
- Wheels and tires
- Body and coating
- Body elements
- Side doors
- Tailgate
- Salon elements
- Safety system
- Windshield wipers and washers
- Body Care
- Electrical equipment
- Instruments and motors
- Battery and alternator
- Egnition lock
- Engine management
- Headlights and lighting
- Switches and sensors
- Schematic diagrams
Focus Turnier 1
- General information
- Introduction to guide
- Car care
- Power unit
- Engine repair
- Lubrication system
- Cooling system
- Fuel injection (gasoline)
- Fuel injection (diesel)
- Ignition system
- Power and exhaust system
- Transmission
- Clutch and drive shafts
- Mechanical gearbox
- Automatic gearbox
- Chassis
- Car suspension
- Steering
- Wheels and tires
- Brake system
- Body
- Exterior
- Interior
- Heating and ventilation
- Electrical equipment
- Equipment and devices
- Lighting and signaling
- Power devices
- Electrical circuits
Focus 1
- General information
- Using the manual
- Identification codes
- Power unit
- Engine
- Engine 1.4/1.6 Zetec-SE
- Engine 1.6/1.8/2.0 Zetec-E
- Engine Duratec ST 2.0 l
- Engine Duratec 8V 1.6 l
- Diesel engine 1.8 l
- Engine cooling
- Fuel supply
- Accessory drive
- Launch system
- Ignition system
- Air and vapor
- Engine management
- Exhaust toxicity
- Exhaust system
- Automatic gearbox
- Clutch
- Mechanical gearbox iB5
- Mechanical gearbox MTX-75
- Mechanical gearbox MT285
- Chassis
- Front suspension
- Rear suspension
- Wheels and tires
- Front axle axles
- Brake system
- Hydraulic brake
- Anti-lock braking system
- Steering
- Body and coating
- Body panels
- Body elements
- Salon elements
- Glass, frames and mechanisms
- Windshield wipers and washers
- Car sunroof
- Seat belts
- Body repairs
- Back elements
- Electrical equipment
- Climate control
- Heating and ventilation
- Instruments and control lamps
- Battery and alternator
- Audio system
- Headlights and lighting
- Power distribution
- Electronic Function Group