Vehicle Emissions Reduction Ford Focus 1

Emissions reduction specifications (1.8/2.0/1.6 Zetec-E)
Tightening torque specification Name Nm pound-foot pound-inch Positive Crankcase Ventilation (PCV) Hose Mounting Bolt 10 - 89 Engine Crankcase Vent Oil Separator...

Description and operating principle (1.8/2.0/1.6 Zetec-E)
Reducing exhaust toxicity Pos. Spare Part No Name 1 Positive Crankcase Ventilation (PCV) Hose 2 Positive Crankcase Ventilation (PCV) Valve 3 Oil separator of the...

Diagnostics and checks (1.8/2.0/1.6 Zetec-E)
Inspection and verification 1. Check the customer complaint. 2. Visually inspect for obvious signs of mechanical damage. Visual inspection table Mechanical factors:...

Positive Crankcase Ventilation (PCV) Hose (1.8/2.0/1.6 Zetec-E)
Removal 1. Disconnect the ground cable from the battery. For additional information, refer to Section 414-01. 2. Drain the coolant from the cooling system. Refer to...

Positive crankcase ventilation valve (PCV) (1.8/2.0/1.6 Zetec-E)
Removal All cars 1. Raise and support the vehicle. Refer to Section 100-02 for additional information. 2. Remove the engine protection. 3. Disconnect the positive...

Emissions reduction specifications (1.8L diesel)
Tightening torque specification Name Nm pound-foot pound-inch Exhaust Gas Recirculation (EGR) Pipe Bolts 20 15 - EGR cooler to cylinder block mounting bolts 23 17 - EGR...

Description and operating principle (1.8 l diesel)
Cars with diesel engine 75 hp or 90 hp. Pos. Spare Part No Name 1 - Exhaust Gas Recirculation (EGR) Pipe 2 - Electronic vacuum regulator EGR 3 - Positive Crankcase...

Diagnostics and checks (1.8 l diesel)
Inspection and verification 1. Check the validity of the customer's complaint by using the system. 2. Visually inspect for obvious signs of mechanical or electrical...

Exhaust Gas Recirculation (EGR) Valve (1.8L Diesel)
Removal 1. Remove the charge air cooler outlet pipe. 1. Release the clamps. 2. Unscrew the nut. 2. Disconnect the EGR valve electrical connector and disconnect the...

Exhaust Gas Recirculation (EGR) Valve (1.8L Diesel Injection)
Removal All cars 1. Remove the top engine cover. Cars with diesel engine 100 hp. 2. Remove the charge air cooler outlet pipe. 1. Release the clamps. 2. Unscrew the nut....

Pipe from the exhaust manifold to the exhaust gas recirculation (EGR) valve
Removal 1. Remove the exhaust gas recirculation (EGR) pipe bolts. 2. NOTE: Mark the position of the clamp so that it is installed in exactly the same position. The loop...

Piping from the exhaust gas recirculation (EGR) cooler to the EGR valve
Removal 1. Remove the charge air cooler outlet pipe. 1. Release the clamps. 2. Unscrew the nut. 2. NOTE: Mark the position of the clamp so that it can be installed in...

Exhaust Gas Recirculation (EGR) Cooler (75 PS/90 PS)
Removal 1. Disconnect the charge air cooler inlet pipe. 1. Release the clamp. 2. Unscrew the nut. 2. Remove the charge air cooler inlet pipe. 3. Remove the charge air...

Exhaust Gas Recirculation (EGR) Cooler (115 PS)
Special tool Clamp removal/installation tool 303-397 (24-003) Removal 1. Disconnect the ground cable from the battery. For additional information, refer to Section...

Engine crankcase ventilation system oil separator
Removal 1. Disconnect the positive crankcase ventilation (PCV) hose. 2. Disconnect the PCV hose. 3. Disconnect the PCV oil separator. 4. Disconnect the PCV hose. 5....