Car engine seal parts Ford Focus 2
Replacing the cylinder head cover gasket
If the oil leak from under the cylinder head cover cannot be eliminated by tightening the cover mounting bolts, replace its gasket. You will need a 12 mm wrench. 1....
If the oil leak from under the cylinder head cover cannot be eliminated by tightening the cover mounting bolts, replace its gasket. You will need a 12 mm wrench. 1....
Replacing the cylinder head gasket
If you detect a leak of engine oil or coolant at the junction of the cylinder head and the cylinder block, remove the head and replace its gasket. The leak may also...
If you detect a leak of engine oil or coolant at the junction of the cylinder head and the cylinder block, remove the head and replace its gasket. The leak may also...
Replacing valve stem seals
An external sign of wear of the oil scraper caps is the short-term appearance of blue smoke from the exhaust pipe after starting the engine and during engine braking...
An external sign of wear of the oil scraper caps is the short-term appearance of blue smoke from the exhaust pipe after starting the engine and during engine braking...
Replacing camshaft seals
If traces of oil leakage through the camshaft seals are detected, first check whether the crankcase ventilation system is clogged or whether the hoses of this system are...
If traces of oil leakage through the camshaft seals are detected, first check whether the crankcase ventilation system is clogged or whether the hoses of this system are...
Replacing crankshaft seals
Front oil seal replace the crankshaft as follows. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the timing belt ( see "Replacing the timing...
Front oil seal replace the crankshaft as follows. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the timing belt ( see "Replacing the timing...
Replacing the oil pan seal
The engine oil pan flange is sealed with FORD WSE-M4G323-A4 sealant gasket. If oil leakage occurs, the seal must be replaced. Perform work on an inspection pit, overpass...
The engine oil pan flange is sealed with FORD WSE-M4G323-A4 sealant gasket. If oil leakage occurs, the seal must be replaced. Perform work on an inspection pit, overpass...
Replacing the intake manifold gasket
There is a gasket installed between the flanges of the cylinder head and the intake manifold. If the seal of this gasket is broken, the engine runs unevenly ("troit")....
There is a gasket installed between the flanges of the cylinder head and the intake manifold. If the seal of this gasket is broken, the engine runs unevenly ("troit")....
Replacing the catalytic converter gasket
A sealing gasket made of a thin molded metal strip is installed between the flanges of the cylinder head and the exhaust manifold. If the seal of this gasket is broken,...
A sealing gasket made of a thin molded metal strip is installed between the flanges of the cylinder head and the exhaust manifold. If the seal of this gasket is broken,...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Focus 2
Focus Turnier 1
Focus 1
- General information
- Vehicle device
- Owner's manual
- Faults en route
- Maintenance
- First maintenance
- Second maintenance
- Applications
- Consumables and spare parts
- Auto mechanic tips
- Power unit
- Engine repair
- Engine seal parts
- Cooling system
- Exhaust system
- Supply system
- Clutch
- Car gearbox
- Front wheel drives
- Chassis
- Front suspension
- Rear suspension
- Steering
- Brake system
- Wheels and tires
- Body and coating
- Body elements
- Side doors
- Tailgate
- Salon elements
- Safety system
- Windshield wipers and washers
- Body Care
- Electrical equipment
- Instruments and motors
- Battery and alternator
- Egnition lock
- Engine management
- Headlights and lighting
- Switches and sensors
- Schematic diagrams
Focus Turnier 1
- General information
- Introduction to guide
- Car care
- Power unit
- Engine repair
- Lubrication system
- Cooling system
- Fuel injection (gasoline)
- Fuel injection (diesel)
- Ignition system
- Power and exhaust system
- Transmission
- Clutch and drive shafts
- Mechanical gearbox
- Automatic gearbox
- Chassis
- Car suspension
- Steering
- Wheels and tires
- Brake system
- Body
- Exterior
- Interior
- Heating and ventilation
- Electrical equipment
- Equipment and devices
- Lighting and signaling
- Power devices
- Electrical circuits
Focus 1
- General information
- Using the manual
- Identification codes
- Power unit
- Engine
- Engine 1.4/1.6 Zetec-SE
- Engine 1.6/1.8/2.0 Zetec-E
- Engine Duratec ST 2.0 l
- Engine Duratec 8V 1.6 l
- Diesel engine 1.8 l
- Engine cooling
- Fuel supply
- Accessory drive
- Launch system
- Ignition system
- Air and vapor
- Engine management
- Exhaust toxicity
- Exhaust system
- Automatic gearbox
- Clutch
- Mechanical gearbox iB5
- Mechanical gearbox MTX-75
- Mechanical gearbox MT285
- Chassis
- Front suspension
- Rear suspension
- Wheels and tires
- Front axle axles
- Brake system
- Hydraulic brake
- Anti-lock braking system
- Steering
- Body and coating
- Body panels
- Body elements
- Salon elements
- Glass, frames and mechanisms
- Windshield wipers and washers
- Car sunroof
- Seat belts
- Body repairs
- Back elements
- Electrical equipment
- Climate control
- Heating and ventilation
- Instruments and control lamps
- Battery and alternator
- Audio system
- Headlights and lighting
- Power distribution
- Electronic Function Group