Car front suspension Ford Focus 1
Suspension specifications
Front wheel alignment angles (at tare weight) - Longitudinal inclination of the wheel steering axis - Vehicles manufactured up to 12.2000. Model Degrees with decimal...
Front wheel alignment angles (at tare weight) - Longitudinal inclination of the wheel steering axis - Vehicles manufactured up to 12.2000. Model Degrees with decimal...
Diagnostics and testing of suspension
Inspection and verification 1. Check the customer complaint. 2. Visually inspect for obvious signs of mechanical damage. 3. If an obvious cause for the problem you have...
Inspection and verification 1. Check the customer complaint. 2. Visually inspect for obvious signs of mechanical damage. 3. If an obvious cause for the problem you have...
Pinpoint tests of suspension
PINPOINT TEST A: LEFT OR RIGHT DRIVE STATES DETAILS/RESULTS/ACTIONS A1: CHECKING FOR LEFT OR RIGHT DRIVE WARNING: To avoid personal injury due to loss of vehicle...
PINPOINT TEST A: LEFT OR RIGHT DRIVE STATES DETAILS/RESULTS/ACTIONS A1: CHECKING FOR LEFT OR RIGHT DRIVE WARNING: To avoid personal injury due to loss of vehicle...
Checking suspension components
Inspection of the ball joint 1. Raise and support the vehicle. Refer to Section 100-02 for additional information. 2. Firmly grasp the outer end of the lower control arm...
Inspection of the ball joint 1. Raise and support the vehicle. Refer to Section 100-02 for additional information. 2. Firmly grasp the outer end of the lower control arm...
Rear wheel alignment adjustment (15 211 0)
General equipment: Wheel alignment equipment (for four wheels). Adjustment 1. NOTE: This operation must be performed with the vehicle on a level, flat, horizontal...
General equipment: Wheel alignment equipment (for four wheels). Adjustment 1. NOTE: This operation must be performed with the vehicle on a level, flat, horizontal...
Front wheel alignment (14 117 0)
NOTE: Checking and subsequent adjustment of the front wheel alignment should be performed on a level, horizontal surface and in accordance with the instructions of the...
NOTE: Checking and subsequent adjustment of the front wheel alignment should be performed on a level, horizontal surface and in accordance with the instructions of the...
Adjusting the calculated suspension height
General equipment: Gearbox jack. All cars 1. NOTE: Final tightening of suspension components should be performed at the calculated suspension height. Remove the spring....
There are 1 a comment
General equipment: Gearbox jack. All cars 1. NOTE: Final tightening of suspension components should be performed at the calculated suspension height. Remove the spring....
There are 1 a comment
Inspection of wheel bearings
Special tool Dial Indicator Stand or Equivalent 100-D004 (D78P-4201-F) Dial indicator or equivalent 100-D005 (D78P-4201-G) Examination 1. Installing new bearings on the...
Special tool Dial Indicator Stand or Equivalent 100-D004 (D78P-4201-F) Dial indicator or equivalent 100-D005 (D78P-4201-G) Examination 1. Installing new bearings on the...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
See other similar sections for Ford cars:
• Chassis: Suspension Ford Mondeo 1 and 2 (1993-2000)
• Chassis: Suspension and wheels Ford Escort 4 (1986-1990)
• Chassis: Car suspension Ford Fiesta 4 (1996-1999)
• Chassis: Car suspension Ford Taurus 1 and 2 (1986-1994)
• Chassis: Suspension Ford Mondeo 1 and 2 (1993-2000)
• Chassis: Suspension and wheels Ford Escort 4 (1986-1990)
• Chassis: Car suspension Ford Fiesta 4 (1996-1999)
• Chassis: Car suspension Ford Taurus 1 and 2 (1986-1994)
Focus 2
Focus Turnier 1
Focus 1
- General information
- Vehicle device
- Owner's manual
- Faults en route
- Maintenance
- First maintenance
- Second maintenance
- Applications
- Consumables and spare parts
- Auto mechanic tips
- Power unit
- Engine repair
- Engine seal parts
- Cooling system
- Exhaust system
- Supply system
- Clutch
- Car gearbox
- Front wheel drives
- Chassis
- Front suspension
- Rear suspension
- Steering
- Brake system
- Wheels and tires
- Body and coating
- Body elements
- Side doors
- Tailgate
- Salon elements
- Safety system
- Windshield wipers and washers
- Body Care
- Electrical equipment
- Instruments and motors
- Battery and alternator
- Egnition lock
- Engine management
- Headlights and lighting
- Switches and sensors
- Schematic diagrams
Focus Turnier 1
- General information
- Introduction to guide
- Car care
- Power unit
- Engine repair
- Lubrication system
- Cooling system
- Fuel injection (gasoline)
- Fuel injection (diesel)
- Ignition system
- Power and exhaust system
- Transmission
- Clutch and drive shafts
- Mechanical gearbox
- Automatic gearbox
- Chassis
- Car suspension
- Steering
- Wheels and tires
- Brake system
- Body
- Exterior
- Interior
- Heating and ventilation
- Electrical equipment
- Equipment and devices
- Lighting and signaling
- Power devices
- Electrical circuits
Focus 1
- General information
- Using the manual
- Identification codes
- Power unit
- Engine
- Engine 1.4/1.6 Zetec-SE
- Engine 1.6/1.8/2.0 Zetec-E
- Engine Duratec ST 2.0 l
- Engine Duratec 8V 1.6 l
- Diesel engine 1.8 l
- Engine cooling
- Fuel supply
- Accessory drive
- Launch system
- Ignition system
- Air and vapor
- Engine management
- Exhaust toxicity
- Exhaust system
- Automatic gearbox
- Clutch
- Mechanical gearbox iB5
- Mechanical gearbox MTX-75
- Mechanical gearbox MT285
- Chassis
- Front suspension
- Rear suspension
- Wheels and tires
- Front axle axles
- Brake system
- Hydraulic brake
- Anti-lock braking system
- Steering
- Body and coating
- Body panels
- Body elements
- Salon elements
- Glass, frames and mechanisms
- Windshield wipers and washers
- Car sunroof
- Seat belts
- Body repairs
- Back elements
- Electrical equipment
- Climate control
- Heating and ventilation
- Instruments and control lamps
- Battery and alternator
- Audio system
- Headlights and lighting
- Power distribution
- Electronic Function Group