Car front and rear suspension Ford Mondeo 1 and 2

Technical requirements and tightening torques
Installing the front wheels Wheel alignment: Acceptable value that does not require adjustment (reverse convergence) 1.5 mm (convergence)...1.5 mm Installation during...

General information about the suspension
1. The front suspension is independent, with MacPherson struts, contains coil springs with telescopic shock absorbers installed inside them and an anti-roll bar. The...

Removing and installing the steering knuckle and hub assembly
Removal 1. Apply the parking brake. Remove the hubcap from the appropriate wheel. Loosen (but do not remove) the drive shaft/hub nut. This nut is tight. 2. Loosen the...

Inspection and replacement of the front hub and bearings
Inspection 1. The front hub bearings are non-adjustable and are supplied lubricated (see Fig. 3.1). 2. To check bearing wear, apply the parking brake, lift the front end...

Removing and installing the front suspension strut
Removal 1. Apply the parking brake. 2. In the engine compartment, remove the strut cap (if present). Holding the strut rod with an Allen key, release the upper support...

Front suspension strut repair
Warning: Before you begin disassembling the strut, prepare a device for compressing the coil springs. Do not use improvised means, as this may cause the spring to jump...

Front cross stabilizer bar
Removal 1. Apply the parking brake. Raise the front of the vehicle and place it on stands. Remove both front wheels. 2. Unscrew the nuts and disconnect the anti-roll bar...
There are 1 a comment

Removal, repair and installation of the lower arm of the front suspension
Note: On the left arm, the front bolt cannot be pulled up (see Fig. 7.0, a, b). Therefore, to remove the bolt, you need to disconnect the power unit from the supports...

Replacing the ball joint of the lower arm of the front suspension
Note: If the ball joint is worn out, you can replace the entire lower control arm assembly or just the ball joint. When the vehicle is manufactured, the ball joint is...

Inspection and replacement of the rear hub and bearings (Sedan and Hatchback)
Note: Once the rear hub is removed, its bearings are no longer usable. Therefore, after removal, the hub must always be replaced together with the bearings. Examination...

Removing and installing the rear suspension axle support (Sedan and Hatchback)
Note: Once the rear hub is removed, its bearings are no longer usable. Therefore, after removal, the hub must always be replaced together with the bearings. Removal 1....

Removing and installing the rear suspension strut (Sedan and Hatchback)
Note: To remove the rear suspension strut, you will need to temporarily compress the coil spring. This is to retract the piston rod into the strut and provide space to...

Rear Suspension Strut Repair (Sedan and Hatchback)
1. The procedure is performed in the same way as the repair of the front suspension strut ( paragraph 5 ). Note that the spring compressors must remain on the spring...

Rear Anti-Roll Bar (Sedan and Hatchback)
Removal 1. Support the front wheels, lift the rear of the car and place it on supports. Remove both rear wheels. 2. Unscrew the nuts securing the stabilizer connecting...

Lower Rear Suspension Arms (Sedan and Hatchback)
Removal 1. Support the front wheels, lift the rear of the car and place it on supports. Remove the corresponding rear wheel. Front lower control arm 2. To remove it, you...

Removing and installing the torque arm (Sedan and Hatchback)
Removal 1. Support the front wheels, lift the rear of the car and place it on supports. Remove the corresponding rear wheel. 2. Disconnect the handbrake cable from the...

Removing and installing the rear suspension beam (Sedan and Hatchback)
Warning: Before removing the beam, prepare a device for compressing the coil springs. Do not use improvised means, as this may cause the spring to jump out, which may...

Inspection and replacement of rear hub and bearings (Station wagon)
Inspection 1. The rear hub bearings are non-adjustable and are supplied with the hub. It is not possible to replace them separately from the hub. 2. To check the...

Removing and installing the rear suspension axle support (Station wagon)
Removal 1. Support the front wheels with chocks. Then lift the rear of the car and place it on supports. Remove the corresponding rear wheel. Release the parking brake....

Removing and installing the rear shock absorber (Station wagon)
Removal 1. Support the front wheels with chocks. Then lift the rear of the car and place it on supports. Remove the corresponding rear wheel. 2. Place a jack stand under...

Rear anti-roll bar (Universal)
1. Support the front wheels, lift the rear of the car and place it on supports. Remove both rear wheels. 2. Unscrew the nuts securing the stabilizer connecting links to...

Rear Suspension Coil Spring (Wagon)
Warning: Before removing the spring, prepare a device for compressing coil springs. Do not use improvised means, as this may cause the spring to jump out, which may...

Rear Lower Control Arm (Wagon)
Removal 1. Remove the rear suspension spring ( paragraph 21 ). 2. The bolt that secures the rear lower arm to the suspension beam has an eccentric head and a spacer...

Front Lower Arm Rear Suspension (Wagon)
Removal 1. Support the front wheels, lift the rear of the car and place it on supports. Remove the corresponding rear wheel. 2. Unscrew the bolt securing the front lower...

Upper control arm rear suspension (station wagon)
Removal 1. Support the front wheels, lift the rear of the car and place it on supports. Remove the corresponding rear wheel. 2. Using a jack stand, support the rear...

Rear Suspension Reactive Arm (Wagon)
1. Support the front wheels, lift the rear of the car and place it on supports. Remove the corresponding rear wheel. 2. Using a jack stand, support the rear lower arm...

Removing and installing the rear suspension beam (station wagon)
Removal 1. Support the front wheels, lift the rear of the car and place it on supports at a height that allows you to remove the beam. Remove both rear wheels. 2....

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Mondeo 4
Mondeo 3
Mondeo 2
Mondeo 1 and 2
Mondeo 1