Exterior (external body parts) Ford Mondeo 1 and 2

Tightening torques for body elements
Tightening torques for connections Name Nm Bonnet and tailgate hinges 24 Trunk lid 10 Bumper mounting nuts 10 Front seat mounting bolts 38 Rear Seat Back Stopper Bolts...

General information about the body
1. All models have a body and its lower frame part made of welded steel. The front and rear parts of the body have special crumple zones designed to absorb energy during...

Body and underbody maintenance
The overall condition of a vehicle's body is one of the parameters that determines its value. Body maintenance is not difficult, but it must be done regularly....

Repair of minor body damage
Restoration of minor car body scratches If only the paintwork is scratched and the metal is not affected, it is very easy to remove the scratch. Lightly rub the scratch...

Repair of serious body damage
If serious damage has occurred or there is a need to restore significant sections of the body due to their malfunction, then in this case it will be necessary to weld...

Removing and installing bumpers
Removal Front bumper - models produced before 1996 1. Apply the parking brake, raise the front end and place it on supports. 2. Disconnect the fog light wiring (if...

Removing and installing the radiator grille
Removal 1. Fix the hood in the open position. 2. On later models, pull out the three fasteners and remove the panel surrounding the hood lock (see Fig. 7.2, a, b). 3....

Removal, installation and adjustment of the hood
Removal 1. Open the hood and lock it in the open position. 2. Disconnect the negative battery cable. 3. Release the insulator clips located on the underside of the hood...

Hood release cable and lever
Removal 1. Open the hood, disconnect the negative battery cable. 2. From inside the car, remove the trim from the B-pillar and pull the moisture seal out of the bottom...

Removing, installing and adjusting the hood lock
Removal 1. Remove the radiator grille ( paragraph 7 ). 2. Release the cable and its sheath from the hood lock. 3. Mark the position of the lock on the engine compartment...

Removing and installing rear door glass
Removal Front glass (with manual window lift) 1. Disconnect the negative battery cable. 2. Remove the door interior trim panel ( paragraph 11 ). 3. Remove the outside...

Removing and installing the door
Removal 1. Disconnect the negative battery cable. 2. Unscrew the screws of the door opening limiter. On the front door it is secured with two screws, on the rear door -...

Removing and installing the outside mirror
Removal 1. On models with power mirrors, disconnect the negative battery cable. 2. Remove the cover, unscrew the screw and remove the pivot glass trim from the front of...

Removing and installing the trunk lid
Removal 1. Disconnect the negative battery cable and open the trunk lid. 2. On the right hinge, remove the trim and separate the wiring from the hinge lever. Pull out...

Removing and installing trunk lid lock components
Removal Lock cylinder - models produced before 1996 1. Disconnect the negative battery cable. 2. After opening the lid, remove the luggage compartment trim from its...

Removing and installing the tailgate
Removal Hatchback 1. Disconnect the negative battery cable. Open the door. 2. The door can be removed by unscrewing the bolts from the hinges and leaving the hinges in...

Removing and installing the tailgate support pillars
Removal 1. Fix the door in the open position. 2. Remove the upper elastic retainer securing the pillar to the door. Then pull the bushing out of the ball joint (see Fig....

Removing and installing tailgate lock components
Removal Door Lock (Hatchback) - Models before 1996 1. Disconnect the negative battery cable. 2. After opening the door to access the lock, pull out the moisture seal....

Windshield and fixed glass
1. The windshield and rear glass on all models, as well as the glass located on the sides of the car in its rear part (station wagon models), are secured with a special...

Removal and installation of moldings and stickers
Removal 1. Slide a strong thread or fishing sand under the molding or emblem. Pull the thread as if filing the element being separated from the body to break the...

General information and adjustment of the sunroof
1. The hatch should open freely, without jamming. When closed, the hatch panel should be flush with the roof panel. 2. If adjustment is necessary, open the sunshade...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Mondeo 4
Mondeo 3
Mondeo 2
Mondeo 1 and 2
Mondeo 1