Electrical equipment and appliances Ford Mondeo 1

General information about on-board electrical equipment
When checking electrical equipment in technical documentation, the car owner encounters the concepts of "voltage, current and resistance". Voltage is measured in volts...

Measuring instruments
For measuring electrical parameters in the on-board circuit, so-called combined measuring devices are available for sale, which combine a voltmeter for measuring...

Measurement technique
Voltage measurement The presence of voltage can be proven with a simple test light or voltage indicator. However, in this case it is only determined whether voltage is...

Installation of additional electrical accessories
1. Insulating tape; 2. Tape loop; 3. Clamping tape; 4. Clamping band with mounting holes; 5. Protective hose; 6. Self-adhesive foam tape Wires that are to be laid to the...

Detecting faults in electrical equipment
When troubleshooting electrical equipment, a systematic approach is important. This is true both when checking failed incandescent lamps and in the case of non-working...

Checking switches for current flow
Most electrical consumers are switched on and off using a manually pressed switch. In addition, there are switches with an automatic drive. Such switches include, for...

Checking the relay
Many electrical circuits have a relay. A switching relay works like a switch. Example: if the high beam headlights are turned on using a manual switch, the relay...

Checking the windshield wiper motor
The windshield wiper motor is installed in the radiator tank, under the windshield. To check it, you need to remove the corresponding casing. Terminal markings The...

Checking the flashing light device
The cycles for the flashing light device and for the hazard warning light system are generated by a relay, the so-called flashing light sensor. The hazard warning light...

Checking the brake light
If the brake light does not come on, first check the fuse in the fuse box. If the fuse is OK, check the brake light bulbs and replace any burnt out bulbs if necessary....

Checking the rear window defroster
When the rear window heating system is turned on, after a certain period of time the area with visible tracks should be free of plaque or ice. If there is a problem,...

Removing and installing the horn
Removal Remove 9 bolts (carburetor engine) or 10 bolts (diesel) of the front cover sheet. Pull wire "23" off fanfare "24". Unscrew the fanfare "22". Installation Screw...

Replacing fuses
In order to avoid damages due to short circuits and overloads in the lines and consumers of the electrical system, individual electrical circuits are protected by fuses....

Location of fuses and relays
Fuse box in the engine compartment № Current strength, A Protected electrical circuit 1 80 Main power supply on-board electrical circuit 2 60 Radiator Fan Motor 3 60...

Anti-theft alarm device
The FORD MONDEO anti-theft alarm is activated, depending on the equipment, by the car key or infrared remote control. Components of the anti-theft alarm system: 1 -...

Removing and installing the instrument panel
In the Fort Mondeo, all instruments are combined on the control panel. After removing the instrument panel, you can remove the instruments or lamps. 1 - Control panel; 2...

Removal and installation of devices
Removal Disconnect the negative (-) cable from the battery. Warning! This will erase data in electronic memory devices, such as the engine fault memory device or the...

Removing and installing the tachometer
Removal Disconnect the negative (-) cable from the battery. Warning! This will erase data in electronic memory devices, such as the engine fault memory device or the...

Steering column switch, turn signal relay
Removal Attention! The switches are located in the multifunctional switch and can only be removed or replaced as a set. In this case, the removal of the left switch...

Removing and installing the radio
Built-in radios are equipped with a plug-in holder by the manufacturer, which allows the radio to be quickly removed and installed. However, this is only possible with...

Removing and installing the loudspeaker
Door mounted speaker Remove the door trim, see item 17.15 . Unscrew the four screws of the speaker and remove it. Disconnect the speaker wire. Connect the wire, screw...

Removing and installing the antenna
Please note: The antenna wire runs from the roof mounting point above the right A-pillar (roof pillar in front of the front door) through the instrument panel. Removal...