Brake system of the car Ford Mondeo 2

General information about the brake system
The Ford Mondeo braking system includes a parking brake system (handbrake) and a diagonally divided service brake system with dual-circuit hydraulic drive. These systems...

Brake design
Mondeo models are equipped with either disc brakes on the front wheels and drum brakes on the rear wheels, or disc brakes on all wheels, i.e. the rear wheels can be...

General description of the braking system
A dual-circuit hydraulic brake system is a system with a diagonally divided hydraulic drive. Accordingly, a separate brake circuit is installed for the front wheel and...

Replacing the front brake pads
If the brake shoe lining is worn to a thickness of 1.6 mm, replace the brake shoe. In this case, the entire set is replaced, and the brake shoes must be from the same...

Removing and installing the front brake caliper
Remove the brake caliper as follows: - unscrew the wheel nuts; - place the front of the car on a jack and remove the wheel; - clamp the hydraulic hose in a suitable vice...

Disassembling the front brake caliper
Disassemble the brake caliper as follows: - partially pull the piston out of the cylindrical hole and press the protective ring with a small screwdriver, press out the...

Removing and installing the front brake disc
Remove the brake disc as follows: - remove the brake caliper as described above and tie it to the suspension with wire so that it does not hang on the hose; Fig. 257....

Removing the rear drum brake shoes
Warning: Use Ford brake pads or Ford approved parts when installing. - Raise the rear of the car and place it on supports; - remove the rear wheels, place chocks under...

Installing rear drum brake shoes
Install the brake pads as follows: Fig. 260. Lubrication points for heated bearings - lightly lubricate the brake pad contact areas shown in Fig. 260 with a compound for...

Removing and installing the brake cylinder of drum brakes
The wheel brake cylinder can be removed without removing the brake pads. Remove the wheel brake cylinder in the following order: - place the car on a jack and unscrew...

Replacing rear disc brake pads
Replace the brake pads as follows: - Loosen the wheel nuts, apply the parking brake, place the rear of the car on supports and remove the wheels; - disconnect the plug...

Removing and installing the rear disc brake caliper
Remove the brake caliper as follows: - loosen the wheel nuts; - Raise the rear of the car on supports and remove the wheel; - release the car with the parking brake; -...

Removing and installing the rear brake disc
Remove the brake disc as follows: - Loosen the wheel nuts, raise the rear of the car on supports and remove the wheel; - remove the brake caliper as described in the...

Removing and installing the master brake cylinder
Warnings: Brake fluid is toxic and will corrode your vehicle's paintwork. Handle it with care. When bleeding the brakes, support the vehicle on jack stands. The...

Repair of the main brake cylinder
The master cylinder must not be disassembled. A new cylinder is supplied without a reservoir, which must be replaced. To remove the reservoir, loosen the two retaining...

Brake booster
When the booster fails, the force on the brake pedal increases significantly, which negatively affects the control of the car. To check the operation of the booster with...

Anti-lock braking system (ABS)
The anti-lock braking system consists of a conventional braking system with diagonally divided brake circuits and a control unit. The control unit includes a hydraulic...

Removing and installing the ABS hydraulic unit
There are two versions of the hydraulic unit (hydraulic unit) available: Mecatronik II and Mecatronik III. To remove the Mecatronik II hydraulic unit, proceed as...

Replacing the ABS sensor (front wheels)
The ABS sensors on the front wheels are located on the steering knuckle. Replace the sensors as follows: - jack up the front of the car to gain access to individual...

Replacing the ABS sensor (rear wheels)
There are differences in the removal procedure depending on the installed brake mechanisms (disc and drum). Removing the sensor in the presence of a disc brake mechanism...

Replacing the front parking brake cables
To remove the parking brake cable and lever, remove the center console. Remove the parking brake cable and lever in the following order: - disconnect the battery; -...

Replacing the rear parking brake cables
Replace the rear parking brake cables as follows: - Raise the rear of the car on supports; Fig. 277. Fastening of thermal insulation protection - remove the...

Traction control system
15.12.1. Removing and installing the adjusting electric motor As already mentioned, this system is installed to order, it works together with ABS. Both systems use the...

Removing and installing the adjusting electric motor
If the adjustment motor has been replaced, adjust the cable connections as well. It is further assumed that only the electric motor is removed and installed, and the...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Mondeo 4
Mondeo 3
Mondeo 2
Mondeo 1 and 2
Mondeo 1