Brake system of the car Ford Mondeo 1 and 2

Technical requirements and tightening torques
Front brakes Type With ventilated discs and floating single-piston caliper Disc diameter: Models with 4-cylinder engines 260.0 mm Models with 6-cylinder engines 278.0 mm...

General information about the braking system
The braking system consists of two circuits, each of which includes two brakes located diagonally. Ventilated disc brakes are installed at the front, and disc or drum...

Replacing the front brake pads
Warning: Always replace both front brake pads at the same time. Replacing the pads on only one wheel may cause uneven braking. Although Ford brake pads are...

Removal, repair and installation of the front brake caliper
Note: See warning paragraph 2 . Removal 1. Apply the parking brake. Loosen the front wheel nuts, lift the front end and place it on supports. Remove the corresponding...

Inspection, removal and replacement of the front brake disc
Note: To prevent uneven braking, both front brake discs should be replaced or reground at the same time. Inspection 1. Apply the parking brake. Loosen the front wheel...

Removal, inspection and installation of the rear brake drum
Note: See. paragraph 4 . Removal 1. Chock the front wheels, release the parking brake and engage first gear (or select the "P" position). Loosen the nuts of the...

Replacing the rear drum brake shoes
Warning: Always replace the pads on both rear brakes at the same time. Replacing the pads on only one wheel may cause uneven braking. Dust from worn pads may contain...

Removal, repair and installation of the rear brake wheel cylinder
Note: Before you begin, you must purchase the necessary spare parts (seal repair kit). Also note that if the pads are dirty due to leaks from the wheel cylinder, they...

Replacing rear disc brake pads
Warning: Always replace the pads on both rear brakes at the same time. Replacing the pads on only one wheel may cause uneven braking. Although Ford brake pads are...

Removal, repair and installation of the rear brake caliper
Replacement 1. Support the front wheels with chocks. Engage first gear (or position "P"). Loosen the rear wheel mounting nuts, lift the rear of the car and place it on...

Removing and installing the master cylinder
Warning: Brake fluid is dangerous. If it comes into contact with your skin, rinse it off immediately and thoroughly. If it gets into your eyes, seek medical attention....

Removing and installing the brake pedal
Removal 1. Move the driver's seat back as far as it will go to create more working space. 2. Remove the ashtray. Then remove the screws and remove the lower part of the...

Brake pedal servo amplifier connection
Removal 1. Disconnect the negative battery cable ( chapter 5 paragraphs 1 ). 2. Remove the master cylinder and power steering unit (paragraphs 11 and 16 ). If desired,...

Inspection, removal and installation of pipelines and hoses
Note: See warning at beginning paragraph 15 on careful handling of brake fluid. 1. Raise the front and rear of the car and place supports underneath them. 2. Inspect the...

Removing air from the hydraulic system
Warning: Brake fluid is dangerous. If it comes into contact with your skin, rinse it off immediately and thoroughly. If it gets into your eyes, seek medical attention....

Checking, removing and installing the vacuum servo booster unit
Examination 1. To check the operation of the servo amplifier, press the foot brake pedal several times to eliminate the vacuum. Then start the engine, holding the pedal...

Vacuum hose and check valve of vacuum servo booster
Removal 1. Press the brake pedal four or five times to remove vacuum from the servo booster. 2. Pull the vacuum hose adapter out of the servo booster rubber bushing. If...
There are 1 a comment

Removing and installing the pressure limiting valve (without ABS)
Note: See warning at beginning paragraph 15 on careful handling of brake fluid. Removal 1. On models not equipped with ABS, two of these valves are installed on the...

Removing and installing the pressure limiting valve (with ABS)
Note 1: The valves are removable only on early models with Mecatronic ABS. On late models with ABS, the valves are not removable. Their functions are performed by the...

Removal and installation of the ABS hydraulic modulator
Note: If any ABS component is faulty, the entire hydraulic modulator unit must be replaced. With the exception of the relay box ( paragraph 22 ) spare parts for this...

Checking, removing and installing the ABS wheel sensor
Examination 1. Before removing, check the wheel sensors with a voltmeter, which must be connected to the sensor's electrical connector. An analog voltmeter is...

Removing and installing the ABS relay box
Note: The information in this section applies only to models produced before 1997 (with Mecatronic hydraulic modulator). Models produced since 1997 (with Bosh hydraulic...

Throttle actuator of the traction control system
Removal 1. This actuator is mounted in the front right corner of the engine compartment. First, disconnect the negative battery cable. 2. For better access, remove the...

Removing and installing the brake light switch
Removal 1. Disconnect the negative battery cable. 2. Remove the lower part of the trim from the front panel (Chapter 11). 3. Disconnect the switch electrical connector....

Removing and installing the handbrake lever
Removal 1. Raise the front and rear of the car and place them on supports. Release the handbrake lever completely. 2. Remove the central console (Chapter 11). 3. Working...

Removing and installing handbrake cables
Removal Primary (front) cable 1. Remove the handbrake lever ( paragraph 26 ). 2. Remove the bushing from the bottom and remove the cable from under the vehicle....

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Mondeo 4
Mondeo 3
Mondeo 2
Mondeo 1 and 2
Mondeo 1