Ford Focus 1 car engine starting system
Launch System Specifications
Tightening torque specification Name Nm pound-foot pound-inch Starter mounting bolts 35 26 - Power supply connections to the starter 12 9 - Starter solenoid connection 6...
Tightening torque specification Name Nm pound-foot pound-inch Starter mounting bolts 35 26 - Power supply connections to the starter 12 9 - Starter solenoid connection 6...
Description and operating principle of the launch system
Pos. Spare Part No Name 1 Starter 2 Ignition switch 3 Starter relay 4 Battery/Starter Cable The starting system is used to turn the engine over at a speed sufficient to...
Pos. Spare Part No Name 1 Starter 2 Ignition switch 3 Starter relay 4 Battery/Starter Cable The starting system is used to turn the engine over at a speed sufficient to...
Diagnostics and testing of the starting system
Inspection and verification 1. Check the validity of the customer's complaint by using the system. 2. Visually inspect for obvious signs of mechanical or electrical...
Inspection and verification 1. Check the validity of the customer's complaint by using the system. 2. Visually inspect for obvious signs of mechanical or electrical...
Pinpoint tests of the launch system
PINPOINT TEST A: ENGINE DOESN'T CRANK, RELAY CLICKS STATES DETAILS/RESULTS/ACTIONS A1: CHECKING THE BATTERY 1 Test the battery using the FDS 2000. For more information,...
PINPOINT TEST A: ENGINE DOESN'T CRANK, RELAY CLICKS STATES DETAILS/RESULTS/ACTIONS A1: CHECKING THE BATTERY 1 Test the battery using the FDS 2000. For more information,...
Starter (1.4L/1.6L/1.8L diesel)
Removal 1. Disconnect the ground cable from the battery. 2. Remove the air cleaner. Refer to Section 303-12 for additional information. 3. Remove the starter bolts. 4....
Removal 1. Disconnect the ground cable from the battery. 2. Remove the air cleaner. Refer to Section 303-12 for additional information. 3. Remove the starter bolts. 4....
Starter (1.8L/2.0L/1.6L Zetec-E)
Removal 1. Disconnect the ground cable from the battery. For additional information, refer to Section 414-01. 2. Disconnect the mass air flow (MAF) sensor electrical...
Removal 1. Disconnect the ground cable from the battery. For additional information, refer to Section 414-01. 2. Disconnect the mass air flow (MAF) sensor electrical...
Starter (Duratec ST 2.0 l)
Removal 1. Remove the intake manifold. For additional information, refer to Section 303-01A / 303-01B / 303-01C / 303-01D / 303-01E. 2. Disconnect the starter plug...
Removal 1. Remove the intake manifold. For additional information, refer to Section 303-01A / 303-01B / 303-01C / 303-01D / 303-01E. 2. Disconnect the starter plug...
Starter (1.6L Duratec)
Removal 1. Disconnect the battery ground cable. Refer to Section 414-01 for additional information. 2. Disconnect the coolant hose support bracket. Loosen the coolant...
Removal 1. Disconnect the battery ground cable. Refer to Section 414-01 for additional information. 2. Disconnect the coolant hose support bracket. Loosen the coolant...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
See other similar sections for Ford cars:
• Engine: Starting and charging systems Ford Mondeo 1 and 2 (1993-2000)
• Engine: Starting and charging systems Ford Mondeo 1 and 2 (1993-2000)
Focus 2
Focus Turnier 1
Focus 1
- General information
- Vehicle device
- Owner's manual
- Faults en route
- Maintenance
- First maintenance
- Second maintenance
- Applications
- Consumables and spare parts
- Auto mechanic tips
- Power unit
- Engine repair
- Engine seal parts
- Cooling system
- Exhaust system
- Supply system
- Clutch
- Car gearbox
- Front wheel drives
- Chassis
- Front suspension
- Rear suspension
- Steering
- Brake system
- Wheels and tires
- Body and coating
- Body elements
- Side doors
- Tailgate
- Salon elements
- Safety system
- Windshield wipers and washers
- Body Care
- Electrical equipment
- Instruments and motors
- Battery and alternator
- Egnition lock
- Engine management
- Headlights and lighting
- Switches and sensors
- Schematic diagrams
Focus Turnier 1
- General information
- Introduction to guide
- Car care
- Power unit
- Engine repair
- Lubrication system
- Cooling system
- Fuel injection (gasoline)
- Fuel injection (diesel)
- Ignition system
- Power and exhaust system
- Transmission
- Clutch and drive shafts
- Mechanical gearbox
- Automatic gearbox
- Chassis
- Car suspension
- Steering
- Wheels and tires
- Brake system
- Body
- Exterior
- Interior
- Heating and ventilation
- Electrical equipment
- Equipment and devices
- Lighting and signaling
- Power devices
- Electrical circuits
Focus 1
- General information
- Using the manual
- Identification codes
- Power unit
- Engine
- Engine 1.4/1.6 Zetec-SE
- Engine 1.6/1.8/2.0 Zetec-E
- Engine Duratec ST 2.0 l
- Engine Duratec 8V 1.6 l
- Diesel engine 1.8 l
- Engine cooling
- Fuel supply
- Accessory drive
- Launch system
- Ignition system
- Air and vapor
- Engine management
- Exhaust toxicity
- Exhaust system
- Automatic gearbox
- Clutch
- Mechanical gearbox iB5
- Mechanical gearbox MTX-75
- Mechanical gearbox MT285
- Chassis
- Front suspension
- Rear suspension
- Wheels and tires
- Front axle axles
- Brake system
- Hydraulic brake
- Anti-lock braking system
- Steering
- Body and coating
- Body panels
- Body elements
- Salon elements
- Glass, frames and mechanisms
- Windshield wipers and washers
- Car sunroof
- Seat belts
- Body repairs
- Back elements
- Electrical equipment
- Climate control
- Heating and ventilation
- Instruments and control lamps
- Battery and alternator
- Audio system
- Headlights and lighting
- Power distribution
- Electronic Function Group