Doors, locks and windows of the car Ford Fusion

Removal and installation the front door trim
You will need: flat- and Phillips-head screwdrivers, TORX T40 key. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the outside mirror control...

Front door glass replacement
You will need a 10 mm socket wrench. 1. Remove the front door trim (see " Removal and installation the front door trim "). 2. Remove the plugs of the two technological...

Replacing the front door window regulator
You will need a 10 mm socket wrench. 1. Remove the front door glass (see " Front door glass replacement "). 2. If you are removing the window regulator for replacement,...

Replacing the outside handle and lock of the front door
You will need: 8 mm keys, TORX T20, TORX T40, flat-head and Phillips-head screwdrivers. 1. Remove the screw securing the door lock switch trim… 2. …and remove the trim...

Replacing the inner handle of the front door lock drive
You will need: flat-head and Phillips-head screwdrivers. 1. Use a screwdriver to pry off the screw cap securing the inner handle… 2. …and remove the plug. 3. Remove the...

Replacing the front door opening limiter
You will need: a 10 mm socket wrench, a TORX T40 wrench. 1. Remove the speaker from the corresponding side of the speaker system (see " Removal and installation speakers...

Removal and installation the front door
You will need: 13 mm keys, TORX T40. 1. Loosen the front door opening limiter mounting bolt and detach the limiter from the door pillar (see " Replacing the front door...

Removal and installation the rear door trim
You will need: a flat-blade screwdriver, a TORX T40 key. 1. Remove the inside handle of the rear door lock (see " Replacing the inner handle of the rear door lock...

Rear door glass replacement
You will need a 10 mm socket wrench. 1. Remove the rear door window regulator (see " Replacing the rear door window regulator "). 2. Carefully lower the drop glass into...

Replacing the rear door window regulator
You will need: a flat-blade screwdriver, a TORX T20 key. 1. Remove the rear door trim (see " Removal and installation the rear door trim "). 2. Remove the speaker from...

Replacing the outside handle and rear door lock
You will need: flat- and Phillips-head screwdrivers, an 8 mm spanner. 1. Remove the screw securing the outer handle trim… 2. …carefully pry up the trim with a...

Replacing the inner handle of the rear door lock actuator
You will need: flat-head and Phillips-head screwdrivers. 1. Use a screwdriver to pry off the screw cap securing the inner handle… 2. …and remove the plug. 3. Remove the...

Replacing the rear door opening limiter
You will need: a 10 mm socket wrench, a TORX T40 wrench. 1. Remove the speaker from the corresponding side of the speaker system (see " Removal and installation speakers...

Removal and installation the rear door
You will need: 13 mm keys, TORX T40. 1. Loosen the rear door opening limiter mounting bolt and detach the limiter from the door pillar (see " Replacing the rear door...

Replacing the tailgate stops
You will need: a flat-blade screwdriver and a 13 mm wrench. 1. Open the tailgate and secure it in the closed position (for example, with a wooden block of suitable...

Removal and installation the rear door trim
You will need: flat-head and Phillips-head screwdrivers. 1. Remove the three screws securing the tailgate trim to the door… 2. …and, using a screwdriver and overcoming...

Removal and installation the decorative trim on the tailgate
You will need a 10 mm socket wrench. 1. Remove the rear door trim (see " Removal and installation the rear door trim "). 2. Remove the license plate lights (see "...

Replacing the tailgate lock
To remove the electric drive of the rear door lock you will need: a flat-blade screwdriver, 8 mm wrenches and a TORX T20. 1. Remove the rear door trim (see " Removal and...

Removal and installation the tailgate
Note: The tailgate is quite bulky and heavy, so we recommend removing it with an assistant. You will need: a flat-blade screwdriver and a 10 mm wrench. 1. Remove the...

Removal and installation the fuel tank filler pipe hatch cover
You will need a flat-blade screwdriver. 1. Open the fuel tank filler pipe hatch cover by unlocking the cover lock with the key. 2. Press the cover lock with a...

Removal and installation the fuel tank filler pipe hatch lock
You will need a flat-blade screwdriver. 1. For ease of operation, remove the fuel tank filler pipe cover from its lever (see " Removal and installation the fuel tank...

Windscreen wiper — general information
All windshield wiper components (brushes, levers, rods and gear motor) can be removed separately if necessary. This subsection describes the removal of the wiper...

Replacing windshield wiper blades
No tools are required to replace the wiper blades. 1. Move the wiper arm away from the glass, overcoming the force of the arm spring. 2. Turn the brush perpendicular to...

Replacing windshield wiper arms and rods
You will need: a 15 mm socket head and a ratchet. 1. Open the hood and place it on the support. 2. Remove the decorative cap from the windshield wiper arm mounting nut....

Windscreen wiper trapezoid assembly with gear motor
You will need: keys "10", "13", "27", TORX T30. 1. Remove the air intake box grille (see " Removal and installation the air intake box grille "). 2. Unscrew the nut...

Rear Window Wiper — General Information
All elements of the rear window wiper (blade, arm and gear motor) can be removed separately if necessary. This subsection describes the removal of the wiper blade and...

Replacing the rear window wiper blade
No tools are required to replace the wiper blade. 1. Move the windshield wiper arm away from the glass, overcoming the force of the arm spring, and remove the wiper arm...

Replacing the rear window wiper arm
You will need a 13 mm wrench. 1. Remove the protective cap from the nut securing the lever to the wiper motor shaft. 2. Unscrew the nut… 3. …and remove the lever from...

Replacement of fixed body glazing
The windshield glass, the rear door glass and the side windows are glued into the body openings. They are replaced using the same techniques, so the work is shown using...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Fusion
Scorpio 1
Scorpio 2
Sierra