Brake system of the car Ford Scorpio 1

Technical characteristics of the brake system
The service brake with anti-lock braking system is actuated by a hydraulic dual-circuit master brake cylinder (tandem type) and additionally by a hydraulic auxiliary...

Replacing the front brake pads
Front brake 1 – caliper bracket, 2 – caliper, 3 – brake pads, 4 – piston, 5 – brake disc, 6 – bracket Attention! It is recommended to replace all front brake pads at the...

Replacing the front caliper
Removal 1. Remove the brake pads (see subsection 11.2.1 ). 2. Disconnect the flexible brake hose connection from the caliper and plug the connection holes with...

Replacing the front brake disc
Attention! The discs of both front brakes must have the same thickness and surface condition, only then will both wheels brake simultaneously. Therefore, it is...

Description of the rear brake design
Rear disc brake 1 – caliper, 2 – caliper holder, 3 – caliper guide pin, 4 – protective cover, 5 – caliper to holder mounting bolt, 6 – deaerator, 7 – handbrake lever, 8...

Replacing rear brake pads
Caution! It is recommended to replace all brake pads of both rear brakes at the same time when at least one of the brake pads reaches the minimum thickness. Brake pads...

Removal and installation the rear caliper
Rear caliper section 1 – pusher, 2 – spring, 3 – washers, 4 – conical thrust surface, 5 – adjusting nut, 6 – shaped washer Attention! Before removing the caliper, drain...

Replacing the rear brake disc
Removal 1. Loosen the nuts securing the corresponding rear wheel. 2. Raise the car and remove the wheel. 3. Disconnect the handbrake cable from the bracket on the rear...

Adjusting the handbrake
Handbrake 1 – handbrake lever, 2 – protective cover, 3 – crossbar, 4 – cable, 5 – adjusting nut with lock nut Handbrake actuator parts Attention! Adjustment of the...

Bleeding the brake system
Bleeding is performed after opening the hydraulic brake circuits, and also whenever the brake pedal becomes "soft" and it is necessary to press it several times for the...

Description of the design of the anti-lock braking system
Anti-lock braking system Location of anti-lock braking system components Operating principle Braking efficiency is greatest when the tire's grip on the road surface is...

Checking the operation of ABS
The electronic control unit also implements the auto-diagnostic function, warning the driver by lighting a control lamp about the occurrence of a malfunction of...

Removal and installation of the ABS hydraulic control unit
Hydraulic unit Ground busbar mounting location on hydraulic unit Removal 1. Turn off the ignition. 2. Reduce the pressure in the hydraulic system. 3. Remove the...

Removal and installation the brake pedal
1. Remove the negative cable from the battery. Attention! Release the pressure in the hydraulic accumulator of the brake system. To do this, turn off the ignition and...

Removal and installation the ABS hydraulic unit accumulator
1. Remove the negative cable from the battery. Attention! Release the pressure in the hydraulic accumulator of the brake system. To do this, turn off the ignition and...

Removal and installation of the pump and motor of the ABS hydraulic unit
1. Remove the negative cable from the battery. 2. Disconnect the high pressure hose from the pump. 3. Disconnect the low pressure hose from the pump and drain the brake...

Replacing the front wheel speed sensor
Removal 1. Loosen the nuts securing the corresponding front wheel. 2. Raise the car and remove the wheel. 3. Unscrew the rotation sensor mounting bolts. 4. Disconnect...

Replacing the rear wheel speed sensor
Caution! The brake fluid in the rear brake circuit is under high pressure. Do not press the brake pedal. Removal 1. Loosen the nuts securing the corresponding rear...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Fusion
Scorpio 1
Scorpio 2
Sierra