Doors, locks and windows of the car Ford Scorpio 1

Removal and installation doors
1. Open the door and disconnect the electrical connector (indicated by the arrow) from the door post. 2. Open the door as far as possible and unscrew the door opening...

Adjusting the door position
1. Open the door and loosen the two "Torgx" screws securing the door lock pin. Loosen the screws enough so that the flange of the lock pin moves slightly when tapped. 2....

Removal and installation the interior door trim panel
Front door 1. Open the door and unscrew the 5 screws (there are 7 screws on the rear door) securing the front and rear edges of the door interior trim panel (the arrows...

Removal and installation exterior door handles
1. Remove the interior door trim panel. 2. Remove the foam rubber covering in the area of the handle control rod. Disconnect the rod from the handle. 3. Unscrew the two...

Removal and installation the door lock cylinder
1. Remove the interior door trim panel. 2. Remove the foam rubber covering in the area of the door lock cylinder. 3. Disconnect the control rod (indicated by the arrow)...

Removal and installation the door lock
1. Remove the interior door trim panel. 2. Remove the foam rubber covering in the area of the door lock. Disconnect the control rod from the outer handle. 3. Disconnect...

Removal and installation the door seal
Door seal 1. Open the door and unscrew the seal mounting screws from the lock side. On the back door, unscrew the screws from the hinge side as well. 2. Carefully lift...

Removal and installation door glass
Screws (1) for adjusting the position of the window lifter 1 – front door, 2 – back door 1. Remove the interior door trim panel. 2. Remove the foam rubber coating. 3....

Removal and installation the window lift mechanism
The window lift mechanism is riveted to the door frame. 1. Remove the interior door trim panel. 2. Remove the foam rubber coating. 3. Lift the glass to the stop and...

Removal and installation decorative side door trims
1. Use a screwdriver to pry the central insert away from the door trim. 2. Unscrew the fastening screws (1) and remove the decorative trim. When removing the trims from...

Removal and installation decorative trims on door glass frames
Attention! To install decorative trims on the door glass frame, you must use a rivet gun. 1. Remove the door seal. Front door 2. Unscrew the nut securing the top trim...

Removal and installation exterior rearview mirrors
1. Remove the decorative triangular cover covering the mirror mounting screw and unscrew the mirror. 2. If an electrically adjustable mirror is installed, remove the...

Removal and installation the rear door
Hatchback body" Rear door hinge attached to the roof (Hathback body) 1. Open the rear door, unscrew 11 screws and remove the interior trim panel. 2. Disconnect the wires...

Removal and installation the trunk door lock cylinder
1. Remove the ground wire from the battery. 2. Open the trunk door, unscrew 11 screws and remove the interior trim panel. 3. Unscrew the six nuts securing the trunk door...

Removal and installation the rear door lock
1. Remove the ground wire from the battery. 2. Open the trunk door, unscrew 11 screws and remove the interior trim panel. 3. Disconnect the control rod (indicated by the...

Removal and installation the gas-filled tailgate strut
1. Open the trunk door and prop it up with a wooden block. 2. Use a small screwdriver to lift the spring clips and remove the gas-filled struts from the ball heads. Do...

Removal, installing and adjusting the trunk lid (Salon models)
1. Open the trunk lid and, using a marker, trace the outline of the hinge along the inside surface of the lid. 2. Remove the decorative panel from the inner surface of...

Removal and installation the trunk lid lock (Salon models)
1. Open the trunk lid. 2. Unscrew the 4 bolts securing the decorative panel of the lid (2 on each side of the lock) and carefully press the 9 clips securing the panel...