Ford Scorpio 1 car engine power system

General information about the fuel system
General information about the fuel system
The fuel system includes the fuel tank, fuel lines, fuel pump, filter, carburetor with air filter or one of the fuel injection systems. The main element of the fuel...

Fuel system specifications
Fuel system specifications
Fuel tank Made from sheet steel, the fuel tank is mounted in front of the rear axle and is held in place by two plates. Capacity 70 dm³ Location of the tank filler neck...

Fuel used for the car
Fuel used for the car
Location of identification letters on the cylinder head with valve seats that ensure operation on unleaded petrol (ONS engine) The location of the identification letters...

Unleaded petrol for V6 engines, 2.4 and 2.9 litres
Unleaded petrol for V6 engines, 2.4 and 2.9 litres
All V6, 2.4 and 2.9 dm³ engines can run on unleaded petrol 95 (Unleaded Premium). On 2.9 dm³ engines with manual transmission installed from December 1988 and models...

Removal and installation the air filter
Removal and installation the air filter
Engines with carburetor Air filter for OHC engines with carburetor 1 – housing, 2 – cover, 3 – filter element, 4 – vacuum diaphragm, 5 – cold air supply pipe Air filter...

Checking the thermostat
Checking the thermostat
Vacuum diaphragm controlling the valve regulating the temperature of the air entering the engine The vacuum diaphragm is indicated by the arrow. Location of the thermal...

Fuel pump — removal and installation
Fuel pump — removal and installation
Mechanical fuel pump Mechanical fuel pump 1 – pusher, 2 – gasket, 3 – fuel pump, 4 – mesh filter, 5 – gasket, 6 – pump cover, 7 – fuel line, 8 – damper On engines with a...

Replacing the fuel filter on engines with a fuel injection system
Replacing the fuel filter on engines with a fuel injection system
1. Remove the ground wire from the battery. 2. Raise the front of the car. 3. Place a suitable container under the filter. 4. Relieve pressure in the fuel system. 5....

Removal and installation the fuel tank
Removal and installation the fuel tank
The fuel tank can be removed after the fuel has been completely used up or if a special pump is available. 1. Remove the ground wire from the battery. 2. If there is...

Removal and installation the fuel level sensor
Removal and installation the fuel level sensor
Removal the fuel level sensor 1. Remove the fuel tank. 2. Unscrew the sensor from the fuel tank using the special Ford tool (Ns 23-014) or two Phillips screwdrivers. 3....

Removal and installation the inertial fuel supply switch
Removal and installation the inertial fuel supply switch
Fuel Pump Inertia Switch Location on Estate Models The inertia switch is shown by the arrow. The inertia fuel switch stops the fuel supply to the system in the event of...

Removal and installation the accelerator pedal
Removal and installation the accelerator pedal
Special tool for loosening accelerator cable clamps 1. Remove the ground wire from the battery. 2. Remove the lower instrument panel trim on the driver's side. 3....

Removal and installation the accelerator cable
Removal and installation the accelerator cable
1. Remove the ground wire from the battery. 2. Disconnect the accelerator cable from the pedal. 3. Remove the cable housing from the bulkhead and pull the cable into the...

Fuel steam separator
Fuel steam separator
Fuel Steam Separator Without Pressure Regulator 1 – return fuel hose, 2 – supply fuel hose, 3 – fuel supply to the carburetor Fuel Steam Separator with Pressure...

Removal and installation the intake manifold
Removal and installation the intake manifold
Fuel Injection System Wiring Harness Connectors The wiring harness connector is indicated by the arrow. Places of application of sealant on mating surfaces The places...




Fusion 
Scorpio 1 
Scorpio 2 
Sierra