Gasoline car engines Ford Sierra

Technical characteristics of gasoline engines
Engines - gasoline, four-stroke, four-cylinder, in-line, water-cooled, have a camshaft in the cylinder head, installed transversely in front of the car. Main parameters...

Tightening torques for threaded connections
Main bearing cap bolts 88 – 102 Nm Connecting rod bolts 40 – 47 Nm Crankshaft pulley bolt 55 – 60 Nm Camshaft gear bolt 45 – 50 Nm Flywheel bolts 67 – 70 Nm Oil pump...

Adjusting valve clearances
Cylinder Head Cover Bolt Tightening Sequence Checking valve clearances 1 – lock nut, 2 – adjusting bolt, 3 – spring, 4 – cam, 5 – pusher (lever), 6 – plate, 7 – valve, 8...

Description of the design of the gasoline engine ONS
Engine components ONS 1 - exhaust manifold, 2 - thermostat, 3 - thermostat housing, 4 - camshaft toothed pulley, 5 - toothed belt housing, 6 - toothed belt, 7 - lever, 8...

Removal and installation the timing belt
Belt cover mounting bolts Removal the timing belt tensioner using key 21.012 1 – tensioner, 2 – spring, 3 – adjusting bolt, 4 – tensioner roller. Installation signs of...

Removal the cylinder head
Air filter assembly 1 – housing, 2 – cover, 3 – filter element, 4 – corrugated air intake hose, 5 – warm air intake 1. Disconnect the ground wire from the battery. 2....

Disassembly and assembly of the cylinder head
Cylinder head assembly 1 – cylinder head cover, 2 – cover gasket, 3 – camshaft bearing bushings, 4 – cylinder head, 5 – camshaft sealing ring, 6 – oil supply line to...

Installing the cylinder head
Cylinder Head Bolt Tightening Sequence Cylinder Head Cover Bolt Tightening Sequence 1. Clean the gasket mating surfaces on the upper surface of the cylinder block and...

Removal and installation the engine
Removal 1. Disconnect the ground wire from the battery. 2. Remove the hood. 3. Remove the air filter. 4. Drain the coolant from the cooling system (disconnect the pipes...

Disassembling the engine
Cylinder Block Assembly 1 – oil pan; 2 – oil pan gasket; 3 – cylinder block; 4 – rear crankshaft seal; 5 – fuel pump gasket; 6 – Coolant pump gasket; 7 – front cylinder...

Identification of interacting parts
Identification of main and connecting rod bearing caps 1–5 – main bearing caps, 6 – connecting rod bearing caps The circle shows the designation of the connecting rod...

Engine assembly
Crank mechanism 1 – crankshaft, 2 – main bearing shells, 3 – main bearing cap, 4 – connecting rod, 5 – connecting rod bearing shell, 6 – piston, 7 – piston rings Gas...

Replacing pistons
Caution! Always replace the four pistons together with the pins. If one cylinder needs to be ground, all pistons together with the pins should be ground and replaced....

Removal and installation the intermediate shaft — removal and installation
Removal and installation the intermediate shaft 1 – cover, 2 – gasket, 3 – sealing ring, 4 – intermediate shaft, 5 – mounting axle plate, 6 – bearing sleeve Removal 1....

Gas distribution system
Camshaft sealing ring Replacement 1. Disconnect the ground cable from the battery and drain the coolant from the cooling system (see subsection 4.1.14.1 ). 2. Disconnect...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Fusion
Scorpio 1
Scorpio 2
Sierra