Cardan shaft and rear axle of the car Ford Sierra
Propeller shaft and rear axle — general information
Cardan shaft The cardan shaft of Ford Sierra cars consists of two parts. In cars with a 1.3 dm³ engine, it has one elastic joint (front), as well as two cross-shaped...
Cardan shaft The cardan shaft of Ford Sierra cars consists of two parts. In cars with a 1.3 dm³ engine, it has one elastic joint (front), as well as two cross-shaped...
Technical characteristics of the cardan shaft and rear axle
Adjustment data Moment of resistance of rotation of the main gear: - bridge 6.5" 1.3 – 1.8 Nm - bridge 7" 1.6 – 2.1 Nm Initial tension of tapered bearings of...
Adjustment data Moment of resistance of rotation of the main gear: - bridge 6.5" 1.3 – 1.8 Nm - bridge 7" 1.6 – 2.1 Nm Initial tension of tapered bearings of...
Removal and installation the propeller shaft
Cardan shaft and drive axles 1 – shaft assembly, 2 – elastic joint, 3 – intermediate bearing, 4 – drive axle shafts, 5 – equilateral three-arm joint, 6 – safety boots, 7...
Cardan shaft and drive axles 1 – shaft assembly, 2 – elastic joint, 3 – intermediate bearing, 4 – drive axle shafts, 5 – equilateral three-arm joint, 6 – safety boots, 7...
Repair of intermediate bearing
Removal the intermediate bearing 1 – intermediate bearing housing, 2 – retaining ring, 3 – bolt, 4 – intermediate bearing, 5 – cross-shaped joint, 6 – U-shaped mounting...
Removal the intermediate bearing 1 – intermediate bearing housing, 2 – retaining ring, 3 – bolt, 4 – intermediate bearing, 5 – cross-shaped joint, 6 – U-shaped mounting...
Removal and installation the rear axle
Rear axle A – spacer sleeve, B – gasket, C – main gear clearance adjustment flange Rear axle 1 – crankcase, 2 – differential bearings, 3 – final drive pinion, 4 – final...
Rear axle A – spacer sleeve, B – gasket, C – main gear clearance adjustment flange Rear axle 1 – crankcase, 2 – differential bearings, 3 – final drive pinion, 4 – final...
Disassembly and assembly of the rear axle
1. Position the rear axle on the appropriate holder (tool 15.070). 2. Unscrew the Torx bolts securing the rear axle cover, remove the cover and drain the oil from the...
1. Position the rear axle on the appropriate holder (tool 15.070). 2. Unscrew the Torx bolts securing the rear axle cover, remove the cover and drain the oil from the...
Disassembling and assembling the differential
Measuring the axial clearance between the axle gears and the differential box Disassembling the differential is only necessary when the gap between the axle gears and...
Measuring the axial clearance between the axle gears and the differential box Disassembling the differential is only necessary when the gap between the axle gears and...
Adjusting the main gear bearings
Main gear pinion with tapered bearings and deformable spacer sleeve 1 – outer tapered bearing, 2 – deformable spacer sleeve 1. Using tools 15.033 and 15.074, remove the...
Main gear pinion with tapered bearings and deformable spacer sleeve 1 – outer tapered bearing, 2 – deformable spacer sleeve 1. Using tools 15.033 and 15.074, remove the...
Adjusting the main gear
1. Install flanges (8, see fig. Rear axle ) adjustment of the differential box bearing clearance without round section gaskets. 2. Install the oiled differential case...
1. Install flanges (8, see fig. Rear axle ) adjustment of the differential box bearing clearance without round section gaskets. 2. Install the oiled differential case...
Assembly and adjustment of the main gear
1. Install the bearings on the differential box, maintaining the previous arrangement of the interacting elements. 2. Install new O-rings and new sealing rings (tool...
1. Install the bearings on the differential box, maintaining the previous arrangement of the interacting elements. 2. Install new O-rings and new sealing rings (tool...
Replacing the final drive gear seal ring
Replacement without removing the rear axle 1. Raise the car. 2. Disconnect the propeller shaft from the main gear flange and hang the shaft from the body. 3. Using tool...
Replacement without removing the rear axle 1. Raise the car. 2. Disconnect the propeller shaft from the main gear flange and hang the shaft from the body. 3. Using tool...
Removal and installation of drive axle shafts
Removal 1. Raise the vehicle and remove the rear wheel on the appropriate side. 2. Remove the brake drum. 3. Unscrew the mounting nut and remove the hub flange using a...
Removal 1. Raise the vehicle and remove the rear wheel on the appropriate side. 2. Remove the brake drum. 3. Unscrew the mounting nut and remove the hub flange using a...
Disassembly and assembly of drive axle shafts
1. Remove the clamps securing the axle shaft joint protective covers. 2. Cut the hinge covers and bend them back using pliers. 3. Using a spring compressor, remove the...
1. Remove the clamps securing the axle shaft joint protective covers. 2. Cut the hinge covers and bend them back using pliers. 3. Using a spring compressor, remove the...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
See other similar sections for Ford cars:
• Transmission: Cardan and rear axle Ford Transit 2 (1986-2000, diesel)
• Transmission: Cardan and rear axle Ford Transit 2 (1986-2000, diesel)
Fusion
Scorpio 1
Scorpio 2
Sierra
- General information
- Vehicle device
- User manual
- Faults on the way
- Maintenance
- Tips for the car owner
- Power unit
- Engine repair
- Lubrication and cooling system
- Supply system
- Exhaust and vapor recovery
- Transmission
- Clutch
- Car gearbox
- Front wheel drives
- Chassis
- Front suspension
- Rear suspension
- Steering
- Brake system
- Wheels and tires
- Body
- Exterior
- Interior
- Doors, locks and windows
- Body сare
- Electrical equipment
- Equipment and devices
- Engine electrics
- Lighting and signaling
- Switches and sensors
- Electrical circuits
Scorpio 1
- General information
- User manual
- Maintenance
- Power unit
- Petrol engines OHC
- Petrol engines DOHC
- Petrol engines V6
- Ignition and control
- Diesel engines
- Cooling system
- Supply system
- Carburetors
- Fuel injection
- Transmission
- Clutch
- Manual gearbox «N»
- Manual gearbox «MT 75»
- Automatic gearbox «A4LD»
- Rear axle and drive shafts
- Chassis
- Steering
- Power steering
- Front suspension
- Rear suspension
- Brake system
- Body
- Exterior
- Interior
- Doors, locks and windows
- Heating and ventilation
- Electrical equipment
- Equipment and devices
- Power devices
- Electrical circuits
Scorpio 2
- General information
- Car care
- Maintenance
- Power unit
- Engine repair
- Lubrication system
- Cooling system
- Ignition system
- Supply system
- Carburetors
- Injection system (gasoline)
- Injection system (diesel)
- Exhaust system
- Transmission
- Clutch
- Car gearbox
- Chassis
- Front suspension
- Rear suspension
- Steering
- Brake system
- Wheels and tires
- Body
- Exterior
- Interior
- Doors, locks and windows
- Heating system
- Electrical equipment
- Equipment and devices
- Headlights and lighting
- Windshield wipers and washers
- Power devices
- Electrical circuits
Sierra
- General information
- User manual
- Maintenance
- Gasoline engines
- Engine repair
- Ignition system
- Fuel system
- Cooling and lubrication system
- Changes 1984-1986
- Changes 1987-1989
- Changes 1990-1993
- Diesel engines
- Engine repair
- Fuel system
- Cooling and lubrication system
- Changes 1988-1993
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Cardan and rear axle
- Chassis
- Steering
- Steering with power steering
- Front suspension
- Rear suspension
- Brake system
- Body and electrical
- Body elements and doors
- Electrical equipment
- Electrical circuits