Inspection and verification
1. Clarify the customer's complaint by verifying that the system is working correctly.
2. Check visually for obvious signs of mechanical or electrical damage.
Visual Inspection Table
Electrical factors:
- Fuse (And)
- electrical connector (s)
- Chain (And)
- Wiring harness
- Module (And) airbags
- Bulb
3. If an obvious cause of a customer-reported or identified fault is identified, correct the fault (if it is possible) before moving on to the next step.
4. If the cause is not visually obvious, connect the diagnostic unit to the data link connector and select the vehicle to be checked from the menu of the diagnostic unit.
5. Trigger the DTCs and refer to the Symptom Chart.
Trouble symptom table
State |
Possible Causes |
Action |
• No communication with module Blinking lamp code: solid. |
• DLC. • Electrical circuit. • Airbag control module. |
• GO to Pinpoint Test A |
• DTC B1231: Longitudinal Acceleration Threshold Exceeded Flashing Lamp Code: Continuous. |
• Collision detected. |
• Unable to clear data in WDS. INSTALL a new airbag control module. REPEAT self-test, CLEAR DTCs. |
• DTC B1318: Low Battery Voltage Flashing Lamp Code: Continuous. |
• Battery. • Charging system. • Electrical circuit. |
• Go to Pinpoint Test B. |
• DTC B1342: Airbag control module is defective. Flashing lamp code: continuous. |
• Airbag control module. |
• INSTALL a new airbag control module. REPEAT self-test, CLEAR DTCs. |
• DTC B1869: Airbag Warning Light Circuit Open or Shorted to "mass". Flashing lamp code: continuous. |
• Dashboard. • Electrical circuit. • Airbag control module. |
• GO to Pinpoint Test C. |
• DTC B1870: Airbag Warning Lamp Shorted to Battery Flashing Lamp Code: Intermittent. |
• Electrical circuit. • Dashboard. |
• GO to Pinpoint Test D. |
• DTC B1876: Driver's Seat Belt Pretensioner Circuit Capacitance Out of Range Flashing Lamp Code: 4 flashes. |
• Driver's seat belt tensioner. |
• Go to Pinpoint test E. |
• DTC B1877: Driver Pretensioner Open Circuit Lamp Flash Code: 4 flashes. |
• Electrical circuit. • Driver's seat belt tensioner. |
• GO to Pinpoint Test F. |
• DTC B1878: Driver Pretensioner Shorted to Battery Flashing Lamp Code: 4 flashes. |
• Electrical circuit. • Driver's seat belt tensioner. |
• GO to Pinpoint Test G. |
• DTC B1879: Driver's seat belt pretensioner circuit is shorted to "mass" Flashing lamp code: 4 flashes. |
• Electrical circuit. • Driver's seat belt tensioner. |
• GO to Pinpoint Test H. |
• DTC B1880: Passenger Belt Pretensioner Capacitance Out of Range Flashing Lamp Code: 4 flashes. |
• Passenger's seat belt tensioner. |
• GO to Pinpoint Test I. |
• DTC B1881: Passenger Pretensioner Open Circuit Lamp Flash Code: 4 flashes. |
• Electrical circuit • Passenger's seat belt tensioner. |
• GO to Pinpoint Test J. |
• DTC B1882: Passenger Pretensioner Shorted to Battery Flashing Lamp Code: 4 flashes. |
• Electrical circuit. • Passenger's seat belt tensioner. |
• GO to Pinpoint Test K. |
• DTC B1883: Passenger Seat Belt Pretensioner Shorted to "mass" Flashing lamp code: 4 flashes. |
• Electrical circuit • Passenger's seat belt tensioner. |
• GO to Pinpoint Test L. |
• DTC B1885: Driver's Pretensioner Circuit Low Resistance Lamp Flash Code: 4 flashes. |
• Electrical circuit. • Driver's seat belt tensioner. |
• GO to Pinpoint M. |
• DTC B1886: Passenger Pretensioner Circuit Low Resistance Lamp Flash Code: 4 flashes. |
• Electrical circuit. • Passenger's seat belt tensioner. |
• GO to Pinpoint Test N. |
• DTC B1915: Driver airbag first stage circuit capacitance out of range. Flashing lamp code: 3 flashes. |
• Driver airbag wiring harness. |
• INSTALL a new airbag harness. REPEAT self-test, CLEAR DTCs. |
• DTC B1916: Driver airbag first stage circuit short to battery. Flashing lamp code: 3 flashes. |
• Clock spring • Electrical circuit |
• GO to Pinpoint Test O. |
• DTC B1920: Passenger Airbag 1st Stage Circuit Capacitance Out of Range. Flashing lamp code: 3 flashes. |
• Electrical circuit. |
• INSTALL a new airbag harness. REPEAT self-test, CLEAR DTCs. |
• DTC B1925: Passenger Airbag First Stage Circuit Shorted to Battery. Flashing lamp code: 3 flashes. |
• Electrical circuit. |
• GO to Pinpoint P. |
• DTC B1932: Driver Airbag First Stage Circuit Open or High Resistance. Flashing lamp code: 1 flash. |
• Driver airbag module. • Clock spring • Electrical circuit. |
• GO to Pinpoint Test Q. |
• DTC B1933: Passenger Airbag First Stage Circuit Open or High Resistance. Flashing lamp code: 2 flashes. |
• Passenger Airbag Module. • Electrical circuit |
• GO to Pinpoint R. |
• DTC B1934: Driver Airbag First Stage Circuit Low Resistance. Flashing lamp code: 1 flash. |
• Driver airbag module. • Clock spring • Electrical circuit. |
• GO to Pinpoint Test S. |
• DTC B1935: Passenger Airbag First Stage Circuit Low Resistance. Flashing lamp code: 2 flashes. |
• Passenger Airbag Module. • Electrical circuit. |
• GO to Pinpoint Test T. |
• DTC B1936: Short Circuit to "mass" the driver's airbag first stage circuit. Flashing lamp code: 3 flashes. |
• Driver airbag module. • Clock spring • Electrical circuit. |
• GO to Pinpoint Test U. |
• DTC B1938: Short Circuit to "mass" passenger airbag first stage circuit. Flashing lamp code: 3 flashes. |
• Passenger Airbag Module. • Electrical circuit. |
• GO to Pinpoint Test V. |
• DTC B1992: Short circuit to driver's side airbag circuit battery Flashing lamp code: 5 flashes. |
• Electrical circuit. • Driver side airbag module. |
• GO to Pinpoint Test W. |
• DTC B1993: Short Circuit to "mass" driver's side airbag circuit Flashing lamp code: 5 flashes. |
• Electrical circuit. • Driver side airbag module. |
• GO to Pinpoint Test X. |
• DTC B1994; Opening of the driver's side airbag circuit Flashing lamp code: 5 flashes. |
• Electrical circuit. • Driver side airbag module. |
• GO to Pinpoint Test Y. |
• DTC B1995: Driver Side Airbag Circuit Low Resistance at Igniter. Flashing lamp code: 5 flashes. |
• Electrical circuit. • Driver side airbag module. |
• GO to the Pinpoint Z test. |
• DTC B1996: Passenger side airbag circuit short to battery. Flashing lamp code: 6 flashes. |
• Electrical circuit. • Passenger side airbag module. |
• GO to Pinpoint AA. |
• DTC B1997: Short Circuit to "mass" passenger side airbag circuit. Flashing lamp code: 6 flashes. |
• Electrical circuit. • Passenger side airbag module. |
• GO to Pinpoint AB. |
• DTC B1998: Passenger Side Airbag Circuit Open Flashing Lamp Code: 6 flashes. |
• Electrical circuit. • Passenger side airbag module. |
• GO to AC Pinpoint Test. |
• DTC B1999: Passenger Side Airbag Circuit Low Resistance at Igniter. Flashing lamp code: 6 flashes. |
• Electrical circuit. • Passenger side airbag module. |
• GO to the AD Pinpoint test. |
• DTC B2117: Driver side airbag module capacitance out of range Flashing lamp code: 5 flashes. |
• Driver side airbag module. |
• GO to Pinpoint AE. |
• DTC B2118: Passenger Side Airbag Capacitance Out of Range Flashing Lamp Code: 6 flashes. |
• Passenger side airbag module. |
• GO to the Pinpoint AF test. |
• DTC B2141: Module Configuration Error - Model Option Content Not Programmed Flashing Lamp Code: 5Hz. |
• New airbag control module not configured. |
• CONFIGURE the airbag control module. See WDS for more information. |
• DTC B2226: Front Impact Sensor Internal Malfunction. |
• Collision sensor |
• INSTALL a new crash sensor. For more information refer to the Collision sensor available in this section. REPEAT self-test, CLEAR DTCs. |
• DTC B2227: Front Impact Sensor Communication Error. |
• Electrical circuit (And) |
• GO to the AG Pinpoint test. |
• DTC B2228: Short circuit to "mass" driver's airbag second stage circuit. |
• Driver Airbag Module • Clock spring • Electrical circuit (And) |
• GO to the AH Pinpoint test. |
• DTC B2229: Short circuit to "mass" passenger airbag second stage circuit. |
• Passenger Airbag Module. • Electrical circuit (And) |
• GO to the AI Pinpoint test. |
• DTC B2230: Driver airbag 2nd stage circuit short to battery. |
• Clock spring • Electrical circuit (And). |
• GO to the AJ Pinpoint Test. |
• DTC B2231: Passenger airbag 2nd stage circuit short to battery. |
• Passenger Airbag Module. • Electrical circuit (And) |
• GO to the AK Pinpoint test. |
• DTC B2232: Driver airbag 2nd stage circuit open. |
• Driver airbag module. • Electrical circuit. |
• GO to the AL Pinpoint test. |
• DTC B2233: Passenger Airbag 2nd Stage Circuit Open. |
• Passenger Airbag Module. • Electrical circuit (And). |
• GO to the AM Pinpoint test. |
• DTC B2234: Driver Airbag 2nd Stage Circuit Low Resistance at Igniter. |
• Driver airbag module. • Electrical circuit (And) |
• GO to the AN Pinpoint test. |
• DTC B2235: Passenger Airbag 2nd Stage Circuit Low Resistance at Igniter. |
• Passenger Airbag Module. • Electrical circuit (And). |
• GO to the AO Pinpoint test. |
• DTC B2477: Airbag Control Module Configuration Error Flashing Lamp Code: Solid. |
• The new airbag control module is incorrectly configured. • The airbag control module is configured for the driver's airbag only, and the vehicle has driver and passenger airbag modules installed. |
• CHECK the equipment of the vehicle. CONFIGURE the airbag control module. See WDS for more information. |
NOTE: • Right hand drive vehicles only. • Electrical circuit |
• GO to the AP Pinpoint Test. |
|
• DTC B2852: Right Side Impact Sensor Short to Battery or "masses". |
• Right side impact sensor. • Electrical circuit (And). |
• GO to the Pinpoint AQ test. |
• DTC B2853: Left side impact sensor short to battery or "masses". |
• Left side impact sensor. • Electrical circuit (And). |
• GO to the AR Pinpoint test. |
• DTC B2854: Left Side Impact Sensor Mismatch with Restraint Control Module. |
• The new side impact sensor is incorrectly configured. |
• CHECK the equipment of the vehicle. CONFIGURE the airbag control module. See WDS for more information. |
• DTC B2855: Front Impact Sensor Shorted to Battery or "masses" |
• Electrical circuit (And). |
• GO to AS Pinpoint Test. |
• DTC B2856: Front Impact Sensor Mismatch with Restraint Control Module |
• The new collision sensor is incorrectly configured. |
• CHECK the equipment of the vehicle. CONFIGURE the airbag control module. See WDS for more information. |
• DTC B2873: Left Side Impact Sensor Internal Malfunction. Flashing lamp code: 5 flashes. |
• Side collision sensor |
• INSTALL a new crash sensor. For more information, refer to Side impact sensor. available in this section. REPEAT self-test, CLEAR DTCs. |
• DTC B2874: Right Side Impact Sensor Internal Malfunction. Flashing lamp code: 6 flashes. |
• Side collision sensor |
• INSTALL a new crash sensor. For more information, refer to Side impact sensor. available in this section. REPEAT self-test, CLEAR DTCs. |
• DTC B2875: Right Side Impact Sensor Mismatch with Restraint Control Module. |
• The new side impact sensor is incorrectly configured. |
• CHECK the equipment of the vehicle. CONFIGURE the airbag control module. See WDS for more information. |
• DTC U2027: Left Side Impact Sensor Configuration Error. |
• Electrical circuit (And). |
• GO to the Pinpoint AT test. |
• DTC U2028: Right Side Impact Sensor Configuration Error. |
• Electrical circuit (And). |
• GO to the AU Pinpoint test. |
Visitor comments