The ignition switch is checked for correct contact closure in different key positions and for the anti-theft device operation. To check the contact group, use a tester in the circuit "ringing" mode: with each key position in the lock, check the correctness of the switch (lock) contact closure according to the electrical equipment diagram.
[For more information, please visit the specified website Fordbook.ru]
Checking the ignition switch (lock) (Focus 2)
This article is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Article reviewed: Mikhail Dmitriev
See other similar articles for Ford cars:
• Replacing the ignition switch (lock) contact group Ford Mondeo 4 (2007-2014)
• Steering column lock / ignition switch Ford Escort 5 (1990-1997)
• Replacing the automatic transmission lock switch Ford Fiesta 2 (1983-1989)
• Replacing the ignition key lock cylinder Ford Taurus 1 and 2 (1986-1994)
• Checking the ignition switch (lock) Ford Fusion (2002-2012)
• Overdrive Lock Switch — removal and installation Ford Transit 2 (1986-2000, diesel)
• Replacing the ignition switch (lock) contact group Ford Mondeo 4 (2007-2014)
• Steering column lock / ignition switch Ford Escort 5 (1990-1997)
• Replacing the automatic transmission lock switch Ford Fiesta 2 (1983-1989)
• Replacing the ignition key lock cylinder Ford Taurus 1 and 2 (1986-1994)
• Checking the ignition switch (lock) Ford Fusion (2002-2012)
• Overdrive Lock Switch — removal and installation Ford Transit 2 (1986-2000, diesel)
Link to this page in different formats
Visitor comments
No comments yet
Focus 2
Focus Turnier 1
Focus 1
- General information
- Vehicle device
- Owner's manual
- Faults en route
- Maintenance
- First maintenance
- Second maintenance
- Applications
- Consumables and spare parts
- Auto mechanic tips
- Power unit
- Engine repair
- Engine seal parts
- Cooling system
- Exhaust system
- Supply system
- Clutch
- Car gearbox
- Front wheel drives
- Chassis
- Front suspension
- Rear suspension
- Steering
- Brake system
- Wheels and tires
- Body and coating
- Body elements
- Side doors
- Tailgate
- Salon elements
- Safety system
- Windshield wipers and washers
- Body Care
- Electrical equipment
- Instruments and motors
- Battery and alternator
- Egnition lock
- Engine management
- Headlights and lighting
- Switches and sensors
- Schematic diagrams
Focus Turnier 1
- General information
- Introduction to guide
- Car care
- Power unit
- Engine repair
- Lubrication system
- Cooling system
- Fuel injection (gasoline)
- Fuel injection (diesel)
- Ignition system
- Power and exhaust system
- Transmission
- Clutch and drive shafts
- Mechanical gearbox
- Automatic gearbox
- Chassis
- Car suspension
- Steering
- Wheels and tires
- Brake system
- Body
- Exterior
- Interior
- Heating and ventilation
- Electrical equipment
- Equipment and devices
- Lighting and signaling
- Power devices
- Electrical circuits
Focus 1
- General information
- Using the manual
- Identification codes
- Power unit
- Engine
- Engine 1.4/1.6 Zetec-SE
- Engine 1.6/1.8/2.0 Zetec-E
- Engine Duratec ST 2.0 l
- Engine Duratec 8V 1.6 l
- Diesel engine 1.8 l
- Engine cooling
- Fuel supply
- Accessory drive
- Launch system
- Ignition system
- Air and vapor
- Engine management
- Exhaust toxicity
- Exhaust system
- Automatic gearbox
- Clutch
- Mechanical gearbox iB5
- Mechanical gearbox MTX-75
- Mechanical gearbox MT285
- Chassis
- Front suspension
- Rear suspension
- Wheels and tires
- Front axle axles
- Brake system
- Hydraulic brake
- Anti-lock braking system
- Steering
- Body and coating
- Body panels
- Body elements
- Salon elements
- Glass, frames and mechanisms
- Windshield wipers and washers
- Car sunroof
- Seat belts
- Body repairs
- Back elements
- Electrical equipment
- Climate control
- Heating and ventilation
- Instruments and control lamps
- Battery and alternator
- Audio system
- Headlights and lighting
- Power distribution
- Electronic Function Group