Vehicle wheel drive shafts Ford Escort 4
Description of the design of drive shafts
Right drive shaft 1, 6 – ball joint; 2 – retaining ring; 3, 5, 7, 9 – clamp; 4, 8 – protective cover; 10 – drive shaft Left drive shaft 1, 14 – ball joint; 2 – flange;...
Right drive shaft 1, 6 – ball joint; 2 – retaining ring; 3, 5, 7, 9 – clamp; 4, 8 – protective cover; 10 – drive shaft Left drive shaft 1, 14 – ball joint; 2 – flange;...
Tightening torques for threaded connections
Lower control arm mounting bolt 55 – 60 Nm Suspension arm support ball joint mounting bolt 48 – 60 Nm Hub mount 210 – 235 Nm Wheel mounting bolt 89 – 90 Nm
Lower control arm mounting bolt 55 – 60 Nm Suspension arm support ball joint mounting bolt 48 – 60 Nm Hub mount 210 – 235 Nm Wheel mounting bolt 89 – 90 Nm
Removing drive shafts
1. Secure the vehicle with the parking brake. 2. Loosen the front wheel mounting bolts and hub nut. 3. Raise the front of the car, unscrew the bolts and remove the...
1. Secure the vehicle with the parking brake. 2. Loosen the front wheel mounting bolts and hub nut. 3. Raise the front of the car, unscrew the bolts and remove the...
Installation of drive shafts
Drive shaft sealing ring 1 – sealing ring; 2 – normal condition of working edges; 3 – worn working edges; 4 – drive shaft; 5 – lubrication 1. Check the condition of the...
Drive shaft sealing ring 1 – sealing ring; 2 – normal condition of working edges; 3 – worn working edges; 4 – drive shaft; 5 – lubrication 1. Check the condition of the...
Disassembling drive shafts
1. Remove the drive shaft. 2. Mark the position of the protective covers and vibration damper on the shaft. 3. Thoroughly clean the outer surface of the drive shaft. 4....
1. Remove the drive shaft. 2. Mark the position of the protective covers and vibration damper on the shaft. 3. Thoroughly clean the outer surface of the drive shaft. 4....
Assembly of drive shafts
1. Fill the interior of the joint with grease, keeping in mind that a different amount of grease should be applied to each side of the joint. 2. To facilitate...
1. Fill the interior of the joint with grease, keeping in mind that a different amount of grease should be applied to each side of the joint. 2. To facilitate...
Replacing the inner hinge protective cover
1. Secure the vehicle with the parking brake. 2. Raise the front of the car. 3. Unscrew the fastening and remove the ball joint from the steering knuckle. 4. If there is...
1. Secure the vehicle with the parking brake. 2. Raise the front of the car. 3. Unscrew the fastening and remove the ball joint from the steering knuckle. 4. If there is...
Replacing the outer hinge protective cover
1. Remove the inner hinge protective cover. 2. Remove the clamps securing the outer hinge protective cover. 3. Remove the inner joint protective cover by sliding it...
1. Remove the inner hinge protective cover. 2. Remove the clamps securing the outer hinge protective cover. 3. Remove the inner joint protective cover by sliding it...
Hinge housing seal
Work on sealing the hinge housing is performed only if there is an adapter flange for installing a protective cover. 1. Remove the drive shaft. 2. Mark the position of...
Work on sealing the hinge housing is performed only if there is an adapter flange for installing a protective cover. 1. Remove the drive shaft. 2. Mark the position of...
Drive shaft faults
Vibration and increased noise when starting off, engine braking and on sharp turns occur when the CV joint or splined shaft connections are worn out, as well as when the...
Vibration and increased noise when starting off, engine braking and on sharp turns occur when the CV joint or splined shaft connections are worn out, as well as when the...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
See other similar sections for Ford cars:
• Transmission: Drive shafts Ford Mondeo 1 and 2 (1993-2000)
• Transmission: Front wheel drives Ford Fusion (2002-2012)
• Transmission: Drive shafts Ford Mondeo 1 and 2 (1993-2000)
• Transmission: Front wheel drives Ford Fusion (2002-2012)
Escort 5
Escort 4
Escort 3
- General information
- User manual
- Maintenance
- Engine
- HCS and Endura-E engines
- CVH and PTE engines
- Zetec and Zetec-E engines
- Gasoline engines
- Diesel engines
- Diesel engines (since 1992)
- Cooling and heating
- Carburetors
- CFI fuel injection
- EFI fuel injection
- SEFI fuel injection
- Exhaust system
- Charging and starting system
- Ignition system
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Drive shafts
- Chassis
- Brake system
- Car suspension
- Steering
- Body
- Electrical equipment
- Light and appliances
- Schematic diagrams
Escort 4
- General information
- User manual
- Maintenance
- Gasoline engines
- OHV engine repair
- CVH engine repair
- Fuel system
- Weber 2V carburetor
- KE-Jetronic injection system
- CFI injection system
- Ignition system
- Diesel engines
- Engine repair
- Fuel system
- High pressure pump
- Cooling and lubrication system
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Drive shafts
- Chassis
- Suspension and wheels
- Steering
- Brake system
- Body
- Body elements
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Lighting system
- Electrical circuits
Escort 3
- General information
- Maintenance
- Characteristics
- Engine
- Disassembly and assembly
- Cooling system
- Lubrication system
- Supply system
- Fuel injection «K-Jetronic»
- Transmission
- Clutch
- Mechanical gearbox
- Hydromechanical box
- Drive shafts
- Chassis
- Front suspension
- Rear suspension
- Steering
- Brake system
- Electrical equipment
- Starting and charging system
- Ignition system
- Ignition «Escort RS 1600»
- Light and appliances
- Schematic diagrams